Windshield Sealant is a one-component polyurethane adhesive-sealer for pasting windshields where an increased safety guarantee is not required. It is used for fixing the front, rear and side windows to the bodies of cars, vans, railway transport and special purpose vehicles. The best results are achieved when using an air gun.
Meets the requirements (specification) of Loctite TEROSON PU 8597 HMLC.
The minimum ready time is 1 hour after application, according to FMVSS (USA) and 4 hours according to the most stringent European crash test standard.
Properties:
– Suitable for applying to the opening of the windscreen made of any material, including aluminum;
– Due to its high initial hardness and exceptionally strong binding properties, no additional fixation of the glass is required;
– Very good resistance to sagging;
– Does not “reach” for the tool;
– High speed of polymerization;
– High shear strength and high shear modulus. Good elasticity even after long-term use;
– Very low electrical conductivity;
– Good adhesion to the residual materials of the old adhesive joint;
– High resistance to UV radiation;
– Excellent adhesion to glass, glass with a ceramic coating and to painted surfaces;
– High European safety standard.
Application: Thoroughly clean the surfaces to be bonded from old glue, paint and other coatings, rust, dirt, grease and oil deposits. Degrease the surface of the windscreen opening at the landing site using 9691 MANNOL Brake Cleaner. Dry. Make sure that there are no damages or defects on the glass surface. To clean the surface and obtain optimal adhesion, it is recommended to sand the glass bonding line with a soft abrasive material. After sanding, clean the surfaces to be bonded using 9974 MANNOL Glas Cleaner and allow the cleaner to dry for 2 minutes. Degrease the surface of the glass using 9691 MANNOL Brake Cleaner. Dry. Heat the cartridge to 50-80 °C for 15 minutes. For large glasses, we also recommend preheating the second cartridge. Apply a thin layer of glue to the bonding points on the glass. It is allowed to apply glue not on the glass, but on the place of its landing in the opening of the windscreen on the body. It is necessary to start applying from the lower edge of the glass in a uniform layer without breaks along the contour and without gaps between the glue layer and the glass. Install the glass in the opening. Press lightly. The glass remains adjustable for 15 minutes. It is advisable to fix with tape, and then leave to dry. Complete polymerization and complete curing of the adhesive takes place within 24 hours. The car is suitable for driving after 1 hour, but in order to avoid displacement of the glass, which can subsequently lead to excessive internal stresses, and then cracks, it is advisable not to use the car at this time. The car itself must be on a flat surface. Bonding is desirable to be performed at room temperature and humidity of 50-60%.
Contact Adhesive is a one-component polyurethane adhesive for windscreens that do not require an increased safety guarantee. It is used for fixing the front, rear and side windows to the bodies of cars, vans, railway transport and special purpose vehicles.
Meets the requirements (specification) of Loctite TEROSON PU 8597 HMLC.
The minimum ready time is 1 hour after application, according to FMVSS (USA), and 4 hours according to the most stringent European crash test standard.
Properties:
– Suitable for applying to the windshield opening of any material, including aluminum;
– Due to its high initial hardness, no mandatory additional fixing of the glass is required;
– Very good resistance to sagging;
– Does not stick to the tool;
– High speed of polymerization;
– High shear strength and high shear modulus. Good elasticity even after long-term use;
– Very low electrical conductivity;
– Good adhesion to the residual materials of the old adhesive joint;
– High resistance to UV radiation;
– Excellent adhesion to glass, glass with a ceramic coating and to painted surfaces;
– High European safety standard.
Application: Thoroughly clean the surfaces to be bonded from old glue, paint and other coatings, rust, dirt, grease and oil deposits. Degrease the surface of the windscreen opening using 9691 MANNOL Brake Cleaner. Dry. Make sure that there are no damages or defects on the glass surface. To clean the surface and obtain optimal adhesion, it is recommended to sand the glass bonding line with a soft abrasive material. After sanding, clean the surfaces to be bonded using 9974 MANNOL Glass Cleaner and allow the cleaner to dry for 2 minutes. Degrease the surface of the glass using 9691 MANNOL Brake Cleaner. Dry. Apply a thin layer of glue to the bonding points on the glass. It is necessary to start applying from the lower edge of the glass in a uniform layer without breaks along the contour and without gaps between the glue layer and the glass. Install the glass in the opening. Press lightly. It is advisable to fix with tape and leave to dry. Complete polymerization of the adhesive takes place within 12 hours. It is advisable not to use the vehicle at this time. The vehicle itself must be on a flat surface. Bonding is desirable to be performed at room temperature and humidity of 50-60 %.
MANNOL 2K-PUR is a two-component polyurethane-based adhesive for reliable bonding and cosmetic repair of various surfaces and parts and especially for repairing leaks and cracks. Quickly and reliably bonds parts made of all plastics and all metals and alloys in any combination. Suitable for concrete, stone and wood. Ideal for quick repairs with long-lasting effects, e.g. for filling cracks and cavities on surfaces of all shapes. Can be used in the repair of vehicles and other machinery as well as in industry, everyday life and offices.
Properties:
– Cures completely in 20-30 minutes at room temperature, after which any mechanical processing is possible;
– After curing it has exceptional elasticity and high durability, which it retains for a long time;
– Has very high adhesive properties;
– Does not change volume during curing – i.e. does not shrink;
– Does not contain water and solvents, is odourless;
– Thixotropic: When applied, it does not run without external influences;
– Absolutely resistant to water, mould and fungal micro-organisms, oil products;
– Resistant to weather influences and ageing. Withstands temperatures from -60 °C to +120 °C.
Application:
1. Thoroughly clean the surfaces to be bonded of old paint and other coatings, dirt, grease and oil deposits. Remove burrs on the front side with a file and shape the pierced surface evenly forming a chamfer. Grind the damaged area with sandpaper within a radius of 5-7 cm around the perimeter of the piercing or the cracks.
2. Degrease using 9691 MANNOL Brake Cleaner. Roughen the surfaces for best results. Allow to dry.
3. Apply an appropriately sized mesh to the inside of the hole or crack to be treated, overlapping the edges of the hole by at least 5 cm. For large holes it is recommended to apply a second layer of mesh, additionally overlapping the first layer by 50 %. On the front side, apply the foil supplied with the kit to the surface to be treated.
Bonding can take place at any temperature and humidity conditions, however a temperature of +10 to +30 °C and a humidity of 50-60 % is optimal.
4. Squeeze out the required quantity of the two components from the double syringe and mix well. The mixing ratio is 1:1. Apply the mixture on the inner side of the reinforcing mesh over the entire treated surface. Smooth out the applied layer with a trowel, taking care not to apply excessive force to avoid squeezing the compound onto the front side.
5. After 10 minutes, remove the foil from the front side, allow the compound to harden and apply MANNOL Epoxy-Plastic 9904 to the treated surface in preparation for further painting.
Setting time 4-6 minutes after mixing. After 8-10 minutes the adhesive is already resistant to deformation. Complete curing takes 20-30 minutes, depending on the surrounding temperature. Do not apply the product at temperatures below 0 °C. Store tightly closed in the original packaging in a cool, dry place at temperatures between +5 °C and +25 °C.
2K-Acryl Fixed Bond is a universal two-component acrylic adhesive for fast and strong bonding of surfaces made of any metals and alloys (steel, stainless steel, cast iron, aluminum, copper, brass, bronze, magnesium, tin, lead, titanium, etc.) and any plastics (including PVC, ABS, nylon, polycarbonate, plexiglass, polyester resins, polyurethane), as well as ceramics, porcelain, rubber, wood with minimal surface preparation. It can be used both in the repair of cars and other equipment, and in industry, at home and in the office, for furniture repair, etc.
It is used for filling cracks, cavities and potholes, incorrectly drilled holes, repairing damaged threads both internal and external, as well as putty for restoring and leveling flat surfaces.
Properties:
– High adhesion strength (shear and tear), and high impact resistance;
– High resistance to aging, oxidation, high and low temperatures. Heat resistance up to 110 °C;
– Resistance to acids, alkalis, water, oil, gasoline;
– Resistant to UV radiation and weather factors, so it is particularly suitable for outdoor use;
– After final solidification, any mechanical processing with chip removal is possible (drilling, sawing, threading, sanding, etc.), and then painting or varnishing;
– No dripping or leaking;
– Perfectly transparent, clean seam (without air bubbles);
– Good adhesion to oiled surfaces.
Application:
Thoroughly clean the surfaces to be bonded from old paint and other coatings, dirt, grease and oil deposits. Degrease using 9691 MANNOL Brake Cleaner. Dry. Bonding can be performed at any temperature and humidity, but the optimal temperature is from +10°C to +30 °C and humidity of 50-60%. Squeeze the glue out of the double syringe and mix the two components thoroughly. Apply the adhesive to the surface to be treated and squeeze the parts to be bonded. Hardens within 5 minutes. Complete solidification occurs in 24 hours.
Epoxy-Plastic is a two-component adhesive based on epoxy resin. Quickly and extremely firmly glues all types of plastic parts: bumpers, headlights, spoilers, etc., or glues them to surfaces made of any metal and alloys, as well as to glass, ceramics, concrete, wood, etc. Thanks to its transparent matte structure, it is ideal for rapid repairs for a long period, for example: for sealing cracks and incorrectly drilled holes, small cavities on surfaces of any shape, restoring damaged threads, both internal and external. It can be used both in the repair of cars and other equipment, and in industry, at home and in the office. Hardens within 5 minutes at room temperature. It polymerizes up to 80% within 30 minutes. Final curing takes place within 2-3 hours, the compound acquires a high mechanical shear strength (3-5 N / mm2) and can withstand temperatures up to +150 °C.
Properties:
– excellent chemical and mechanical resistance;
– hardens quickly under all conditions, even under water;
– durable, shock-resistant;
– after final solidification, any mechanical processing with chip removal (threading, sanding, etc.) is possible, and then painting or varnishing;
– glues glass, ceramics, concrete, wood and their combinations.
Application: Thoroughly clean the surfaces to be bonded from old paint and other coatings, dirt, grease and oil deposits. Degrease using 9691 MANNOL Brake Cleaner. Dry. Bonding can be performed at any temperature and humidity, but the optimal temperature is from +10 °C to +30 °C and humidity of 50-60%. Squeeze out the required amount of the two components from the tube and mix. The mixing ratio is 1: 1. Then apply to the surfaces that need to be glued or repaired and press them tightly together with maximum force. Store tightly closed in the original packaging under dry conditions from +5 °C to +25 °C.
Ultra-fast adhesive that creates a strong, durable, long-lasting bond. Quick and easy to apply. Works well both on non-porous materials such as metal, plastic, rubber and vinyl as well as on paper, wood and textile.
Super Glue Gel is designed for instant and extremely strong bonding of all types of plastics, ceramics, china, glass goods, metals, polyvinyl chloride, vinyl, wood, paper, cement, leather, marble, as well as their compounds.
Epoxidkitt is a two-component super-putty based on epoxy resin for quick repairs with a long-lasting effect. Fills holes, scratches, cracks, cavities, and dents. Easily mixed by hand and takes any shape. Designed to repair surfaces made of any metals and alloys (steel, cast iron, aluminum, copper, brass, bronze, magnesium, tin, lead, etc.) and any plastics. It can be used to eliminate leaks in the gas tank, radiator, oil pan, barrels, pipes, etc. Applicable under water. Retains its properties up to 260 °C.
Properties:
– Excellent chemical and mechanical resistance;
– Hardens quickly under all conditions, even under water;
– Durable;
– After final solidification, any mechanical processing with chip removal is possible (drilling, sawing, threading, sanding, etc.), and then painting or varnishing;
– does not contain asbestos and is an electrical insulator;
– can be used for glass, ceramics, concrete, wood, etc.
Application: Thoroughly clean the surface of old paint and other coatings, dirt, fat and oil deposits. Degrease using 9691 MANNOL Brake Cleaner. Dry. For best adhesion, the surface can be roughened with sandpaper. Putty can be made at any temperature and humidity, but the optimal temperature is from +10 °С to +30 °C and humidity of 50-60%. Squeeze out of the tube and cut off the desired amount. Mash with your hands until a homogeneous warm mass is obtained. Flatten and remove excess with a spatula. Curing begins in 15 minutes. Complete hardening occurs in 1 hour. When applied under water or on an oiled surface, the compound must be pressed with a spatula until it begins to harden.
Rearview Mirror Adhesive 9934-a set with glue designed specifically for gluing metal plates of rearview mirror mounts (“piglets”) to the windshield, as well as for gluing various metal parts (hinges, locks, fasteners, etc.) to the side windows and windows of the car. At the same time, it is also suitable for gluing any metal and plastic parts in everyday life and various industries (furniture, for example). It can be used for all car brands. It is irreplaceable and effective for planned and emergency repairs, modernization and interior decoration of vehicles, watercraft, motorcycles, sports equipment, household appliances, etc. It can be used for gluing antennas and linings to the body.
Properties:
– Highly stable-resistant to high loads, vibration, strong temperature changes and UV radiation;
– Suitable for installing mounting plates or legs (brackets) of mirrors of all sizes and materials;
– Hardens quickly and holds perfectly;
– Perfectly compensates for the difference in thermal expansion of bonded materials.
Application: Remove the mirror from the mounting plate, if the design provides for it. Mark the initial position of the plate / foot (bracket) on the outside of the windscreen. Thoroughly clean the surfaces to be bonded from glue residues, dirt, grease and oil deposits. For degreasing, we recommend using 9691 MANNOL Brake Cleaner. Carefully unpack the activator& cleaner napkin. Try not to touch the napkin, use the packaging as a cover, as indicated on the packaging of the napkin. Use it to wipe the area of the glass that will be in contact with the mounting plate/foot (bracket) of the mirror. The plate/leg (bracket) itself does not need to be wiped. Allow the activator to dry for 1-2 minutes. Apply only one large drop of glue to the middle of the plate/leg (bracket), do not spread it over the surface. Press firmly and hold for 1-2 minutes until the glue hardens. Wait 15 minutes before installing the mirror on the mounting plate.
Epoxy-Metal is a two-component adhesive based on epoxy resin. Quickly and reliably glues parts made of any metals and alloys (steel, cast iron, aluminum, copper, brass, bronze, magnesium, tin, lead, etc.) in any combination. Ideal for rapid repairs with long-term effect, for example: for sealing cracks and cavities on surfaces of any shape, restoring damaged threads, both internal and external. It can be used both in the repair of cars and other equipment, and in industry, at home and in the office. Hardens within 4 minutes. Final curing takes place within 2-3 hours, the compound acquires a high mechanical shear strength (3-5 N / mm²) and can withstand temperatures up to +150 °C.
Properties:
– excellent chemical and mechanical resistance;
– hardens quickly under all conditions, even under water;
– durable;
– after final solidification, any mechanical processing with chip removal (threading, sanding, etc.) is possible, and then painting or varnishing;
– can be used as a putty for flat surfaces;
– glues glass, ceramics, concrete, wood and their combinations.
Application: Thoroughly clean the surfaces to be bonded from old paint and other coatings, dirt, grease and oil deposits. Degrease using 9691 MANNOL Brake Cleaner. Dry. Bonding can be performed at any temperature and humidity, but the optimal temperature is from +10 °C to +30 °C and humidity of 50-60%. Squeeze out the required amount of the two components from the tube and mix. The mixing ratio is 1: 1. Then apply to the surfaces that need to be glued or repaired and press them tightly together with maximum force.
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. Privacy PolicyAccept
Reviews
There are no reviews yet.