Chain Lube – fully synthetic white lubricant in the form of an aerosol for high-load and high-speed drive chains of motorcycles, ATVs, scooters and other motor vehicles, as well as bicycles. Suitable for all types of chains (O-ring, X-ring, W-ring).
Properties:
– It has increased stickiness and holds well on the fastest moving chains under the action of centrifugal forces, providing reliable lubrication in all modes;
– Unique additive package and contained micro – ceramic elements-friction modifiers provide excellent anti-friction and anti-wear properties;
– Has good water resistance, does not wash off with hot water when washing equipment;
– Smoothly cares for chain seals of any cross-section (O-ring, X-ring, W-ring);
– Resistant to low ambient temperatures and high (up to 260 °C) operating temperatures;
– Reliably protects chains from corrosion;
– Prevents chains from stretching, extending their service life;
– Neutral to rubbers, plastics and paint coatings.
Application: before applying 7901 MANNOL Chain Lube, it is recommended to clean the chain with 7904 MANNOL Chain Cleaner. Spray the grease on the chain. After evaporation of the solvent (5-10 minutes), the lubricant acquires its final properties – the final consistency and the required adhesion.
Contact Cleaner is a special cleaning agent for fast and effective cleaning and degreasing of dirty and rusted electrical contacts of all types.
Ideal for:
– cleaning of electrical blocks and contacts, electronic circuit boards and terminal blocks, lamp bases, cable lines, communication relays, interrupters, ignition distributors, starters, generators, fuses, etc. in cars;
– plug sockets, clamps, electrical distribution devices, battery contacts in industry and everyday life;
– audio and video equipment, office and commercial electrical equipment – cash registers, electronic scales, scanners, etc.
Properties:
– Quickly, efficiently and carefully cleans electrical contacts and connectors, as well as electronic elements from fat and oil films, oxides, phosphates, dust and other insulating contaminants. Reduces the electrical resistance of the contacts and thereby reduces the power loss of electrical equipment and stabilizes the voltage;
– Displaces moisture, forms a water-repellent film;
– Quickly evaporates without leaving traces and eliminates current leaks and short circuits;
– Provides long-term protection of electrical contacts from oxidation, while maintaining their conductivity;
– Due to its high penetration capacity, it improves the efficiency and reliability of electronic systems and electrical equipment, preventing failures and failures;
– Silicone-free, safe for plastic and rubber parts, as well as for paint coatings;
– Can be used for degreasing metal surfaces.
Application:
Before cleaning, disconnect the electrical circuit. Spray MANNOL Contact Cleaner on dirt and leave for 5-10 minutes to act, depending on the intensity of the contamination. Remove dissolved dirt with a cloth or brush. Remove excess product with a damp cloth. In case of contact with the surface of plastic and lacquered parts, remove the composition with a damp cloth. Before connecting to the electrical circuit, wait 10 minutes for the solvent residue to evaporate.
Air Filter Oil-special ultra-sticky impregnation for low-resistance air filters (HIGH-FLOW AIR FILTER) – in common language use «zero-it” or “zero-resistance filters”. It is suitable for use in all 2-stroke and 4-stroke motorcycles and scooters with air-and water-cooled engines, as well as in any other equipment in which such filters are installed normally or as tuning details.
Properties:
– Provides maximum air supply, increasing engine power;
– Reliably holds dust, dirt and sand in the most extreme conditions. Reduces wear and extends the oil change interval. Eliminates engine damage caused by contamination, extends its life and reduces maintenance and repair costs;
– Provides excellent adhesive properties of the filter, so that it effectively detains even the smallest dust particles, while it is securely held on the surface of the filter elements;
– Recommended for use in Motorsport;
– Colors the filter in tints from pale pink to red, and the color may appear immediately or after a while;
– Completely eliminates the risk of destruction of HIGH-FLOW filters during operation.
Application: Remove the filter. Clean the filter surface from coarse dust and dirt particles by tapping and then using a soft-pile brush. Apply MANNOL Universal Cleaner 9972 on both sides of the filter. Let it soak in. After 10 minutes, rinse the filter in a container of water, then under a low stream of water. Dry the filter well. Shake the container and spray 9964 MANNOL Air Filter Oil on the filter from a distance of 20-30 cm. Mash the filter to achieve the best penetration of the impregnation into the filter. Let it dry for 15 minutes.
Intake Valve Cleaner-a highly effective tool for cleaning the intake system of gasoline engines up to the intake valves and in the most inaccessible places from all the typical dirt without disassembling the system. In most cases, a single application is sufficient to bring the intake system into perfect condition.
As the idling valve (IAC) is operating, deposits gradually accumulate on it, which ultimately affects the circulation of air and gases. This reduces engine power and acceleration, disrupts the smoothness of idling, and significantly increases fuel consumption. Signs of a clogged idle valve may include:
– Difficult start-up;
– Intermittent idling, as indicated by jumping tachometer readings;
– Slow speed reduction when you press the clutch pedal while driving;
– Black smoke from the exhaust pipe.
Properties:
– Quickly, effectively and carefully removes dirt, soot, carbon, resinous and oil deposits and other most difficult to remove and old dirt;
– Further protects the intake system elements from corrosion and oxidation, prevents the formation of new dirt and deposits on them, provides functionality and mobility of moving parts, – extending the service life of the intake system and reducing repair costs;
– Facilitates cold start, restores the uniformity of idle speed, and reduces fuel consumption;
– Contains acetone-aggressive to paint surfaces and plastics;
– Safe for catalytic converters, oxygen sensors and turbochargers.
Application: shake the balloon well before use. The product must be sprayed behind the air flow meter (the product must not get on it) for at least 30 seconds (depending on the degree of contamination) when the engine is idling (at least 2000 rpm).
If there are particularly persistent deposits on the throttle, inside the intake manifold, or on the intake valves, the cleaning procedure can be repeated. After application, allow the engine to run for about 20 seconds at min. 2000 rpm, so that possible residues in the intake system can burn.
Carburetor Cleaner – highly effective carburetor cleaner without dismantling it. Quickly, carefully and effectively cleans throttle and air dampers, diffusers, jets and all other available internal surfaces of carburetors, as well as their external surfaces. Applicable to all two – or four-stroke gasoline engines, with or without catalytic converters.
Properties:
– It is a mixture of highly effective organic solvents. Does not contain acetone;
– Completely dissolves and removes all typical carburetor contaminants of various origins;
– Does not clog the engine components located behind the carburetor: valves, combustion chamber, etc.;
– Stabilizes idle speed, facilitates cold start, improves engine acceleration;
– Optimizes the operation of the intake system by cleaning and lubricating its moving parts;
– The product contains substances that are aggressive to paint surfaces and plastics;
– Reduces fuel consumption (up to 5%) and exhaust gas toxicity;
– Applicable for cleaning motorcycle chains, timing chains, clutch parts, oil pumps, gears, crankshafts and other unpainted metal components and engine parts.
Application. Turn off the engine and remove the air filter. You need to get direct access to the throttle. Spray the product on all internal surfaces of the carburetor located in the access area, as well as, if necessary, on external surfaces. Let them dry. Replace the air filter in its original position. It is advisable to replace it at the same time. Turn on the engine and let it run at medium speed, and you can already start driving. You can also let the engine run at idle for 20 seconds at 2000 rpm, so that the remaining dirt in the injection system can burn.
If the engine allows, i.e. can maintain a stable speed when the air intake is disconnected, then cleaning can be performed when the engine is turned on. If this doesn’t work, contact the service center to find out how to do it. Sometimes it is enough to turn off the air flow meter. When the engine is running, the cleaning process is significantly intensified. At the same time, do not allow the product to get on the air flow meter and painted parts.
Motor Cleaner is a detergent for cleaning and care of the engine compartment of the vehicle. Quickly, efficiently and carefully removes most of the typical engine compartment dirt: oils, residues of evaporated and burnt technical fluids, road dirt and dust, road reagents, etc. It has a high cleaning capacity. A clean engine is less likely to overheat.
– Has an increased solvent capacity and active cleaning properties;
– High-viscosity concentration allows components to remain on vertical surfaces, providing excellent cleaning of complex contaminants in all dimensions;
– Neutral in relation to coatings made of chrome, nickel, zinc, etc., as well as to the surfaces of ferrous and non-ferrous (aluminum, bronze, brass, etc.) metals and alloys. It can be aggressive towards certain types of plastics, rubbers and paint coatings;
– Further prevents oxidation, cracking and loss of properties of rubber and plastic parts of the engine under the aggressive influence of pollution and the environment, prevents oxidation of electrical connections, reduces the risk of short circuits, prevents fire of electrical wiring;
– Can be used for cleaning various units of cars, motorcycles, trucks, tractors and other agricultural, garden and construction equipment, as well as water equipment: chassis, filters, pumps, auto and motorcycle-free drive chains, etc. , as well as various inventory and working tools;
– It is recommended to use at the end of the “dirty” season, before and after engine, suspension or transmission repairs, as well as during pre-sale preparation of the car.
Application: Spray the product on the parts to be cleaned from a distance of 15-20 cm, holding the container vertically. Leave to act for 3-5 minutes, depending on the degree of contamination. Wipe with a brush or sponge, and then rinse with water. Repeat the procedure if necessary. Before applying, try the cleaner on a small inconspicuous area to find out possible reactions with different materials.
Motor Kaltreiniger – highly effective detergent for cleaning and maintenance of the engine compartment of the car. Quickly, efficiently and carefully removes any contamination of the engine compartment: oil, residues of evaporated and burnt technical fluids, road dirt and dust, road reagents, etc. Softens and dissolves the most difficult to remove and old dirt. A clean engine is less likely to overheat.
– Has an increased solvent capacity and active cleaning properties;
– Active foam stays on vertical surfaces for a long time, providing excellent cleaning of complex dirt in all dimensions;
– Neutral in relation to plastic, rubber, paint coatings, chrome, nickel, zinc, etc., as well as to the surfaces of ferrous and non-ferrous (aluminum, bronze, brass, etc.) metals and alloys;
– Further prevents oxidation, cracking and loss of properties of rubber and plastic parts of the engine under the aggressive influence of pollution and the environment, prevents oxidation of electrical connections, reduces the risk of short circuits, prevents fire of electrical wiring;
– Can be used for cleaning various aggregates of cars, motorcycles, trucks, tractors and other agricultural and construction equipment, as well as water equipment: chassis, filters, pumps, tools, auto and motorcycle drive chains of all types, garden equipment and tools;
– It is recommended to use at the end of the “dirty” season, before and after engine, suspension or transmission repairs, as well as during pre-sale preparation of the car;
– Can be used for cleaning concrete floors from oil.
Application: Spray on the parts to be cleaned from a distance of 20-30 cm and leave to act for 10-20 minutes, depending on the degree of contamination. Then rinse thoroughly with a strong stream of water.
Catalytic System Cleaner is a professional tool for cleaning and restoring the efficiency of catalytic converters. Suitable for all gasoline engines, both naturally aspirated and turbocharged, equipped with these systems. It also allows you to clean the power supply system and fuel injection devices of a gasoline engine from all typical contaminants without disassembly.
Properties:
– Cleans valves, piston rings, working surface – catalytic Converter cells, exhaust system from carbon deposits, tar and other deposits. Removes carbon deposits from the walls of the combustion chamber and from the grooves of the piston rings, preventing their occurrence;
– Helps to clean the oxygen sensor electrodes (lambda probe);
– Restores the original engine power by reducing the hydrodynamic resistance of the exhaust system;
– By optimizing the combustion process and eliminating contamination of the fuel and exhaust systems, it reduces fuel consumption and exhaust gas toxicity;
– In the future, with a long-term effect, it protects the catalytic converter from blockages, and the fuel system from corrosion;
– Increases the service life of the catalytic Converter and the entire exhaust system.
Application: connect the injection device to the cylinder. Insert (stick) its needle into the rubber hose of the engine air intake and hang the balloon upside down (for example, by the edge of the raised hood) as a dropper. Turn on the flow of funds. Allow the engine to idle at 1500 rpm for approximately 30-45 minutes. Do not allow the engine to overheat. If the exhaust manifold starts to glow red (due to high temperature), stop cleaning immediately.
DPF Foam cleaner is a professional tool for cleaning and restoring
the efficiency of diesel particulate filters (DPF) without dismantling them. Suitable for all diesel engines, both naturally aspirated and turbocharged equipped with these filters. Applicable for diesel engines equipped and not equipped with automatic regeneration systems for diesel particulate filters. Suitable for all ages.
Properties:
– Starts the process of regeneration of the particulate filter. Promotes complete burning of accumulated soot, loosening it and acting as a combustion catalyst;
– Especially effective for vehicles operating in urban mode and in the cold season;
– Restores the full capacity of the particulate filter;
– Restores the original engine power by reducing the hydrodynamic resistance of the filter. Saves fuel;
– Neutral low-ash formula. It evaporates without a trace and is removed from the filter.
– Extends the service life of the particulate filter and reduces the cost of car operating. Regular use may eliminate the need to replace the DPF altogether;
– Reduces the toxicity of exhaust gases.
Application: Remove one of the particulate filter sensors (pressure or temperature). Insert the spray gun into the orifice. Turn on the engine and clean at idle. Spray the content of the balloon towards the particulate filter periodically for 10 seconds with 3-5 seconds intervals until the content is exhausted. Stop the engine. Install the particulate filter sensor in place. Check the cleaning efficiency with a tester on the stand or with a test drive. After regeneration, make sure that the on-Board computer does not issue an error code again. Keep in mind that in some cases you may need to delete errors manually. To keep the particulate filter clean, use the 9994 Mannol filter cleaner in the future between service periods.
Specifications : SAE 0W-40 / 0W40 / ACEA A3/B4 / API SN/CH-4
Recommendation / OEM Approval : ACEA A3/B4 / BMW LL-04 / VOLKSWAGEN 502 00 / VOLKSWAGEN 505 00 / MB 229.5 / MB 229.3 / PORSCHE A40 / RENAULT RN17 / RENAULT RN0700 / RENAULT RN0710 / GM LL-A-025 / GM LL-B-025 / FIAT 9.55535-M2 / FORD WSS-M2C937-A / CHRYSLER MS-10725 / CHRYSLER MS-12633 / Additional_Recommended_Applications for AMG
Product Details
Universal bi-synthetic (PAO + esters) premium motor oil designed for new generations of all types of engines. Designed in accordance with the requirements of German automakers.
Product properties:
– A unique bi-synthetic (PAO + esters) base with an expanded range of viscous and temperature properties ensures effective engine operation in all operating modes: during cold start, in city mode, in highway mode, as well as at increased load (when driving on the road, uphill, with a trailer, maximum load) and at high ambient temperatures:
– Due to its excellent washing-dispersing properties and the highest thermal-oxidative stability, it effectively fights against all types of deposits and keeps engine parts and turbochargers clean throughout the entire interval between replacements;
– Low viscosity bi-synthetic base (PAO + esters) and a highly effective additive package provide reliable cold start in the most severe conditions, which significantly reduces engine starting wear;
– Due to the exceptional strength of the oil film created by the ester components, it has excellent anti-seize, anti-wear and anti-friction properties, which allows to save fuel and, combined with excellent pumpability, significantly increase engine life even in “start-stop” driving modes;
– It is used in engines with extended oil change intervals (Long Life up to 30,000 km) and conventional;
– Due to the high thermo-oxidative stability, it effectively resists aging;
– Has increased resistance to fuel of variable quality and effectively resists liquefaction by fuel.
Designed for gasoline and diesel engines (with and without turbocharging) a wide fleet of cars (cars, light SUVs, minibuses and light trucks of European and other manufacturers), where the performance level of API SN / CH-4 and lower, as well as ACEA A3/B4.
Recommended for use in engines of Daimler, BMW, VW cars, which impose additional requirements for engine oils (according to the above specifications).
The oil is not suitable for use in heavy trucks and similar vehicles!
Brake Cleaner – universal ultra-effective degreaser for metal surfaces. It is used primarily for cleaning surfaces in vehicles and everyday life intended for subsequent processing (gluing, painting, coating, sealants, etc.)
– Contains acetone, aggressive to paint coatings, some plastics and rubbers. Before use, it is necessary to check its effect on a specific material or coating. If negative effects are detected, these surfaces must be protected to avoid chemical damage;
– Removes grease and oil contamination, silicones, certain types of paint coatings, chemical residues, dirt, dust, plaque and other contaminants that will impair the adhesion of the treated surface with the materials applied to it (lacquers, paints, adhesives, sealants, etc.);
– dries quickly, leaves no traces;
Recommended for cleaning brake discs and pads – extends their service life with regular use.
Application: can be applied by flushing, dipping, spraying and pouring. Large parts and components are best treated with spray or wet with wide brushes, rags or similar means. It is usually enough to spray the degreaser on dirty surfaces and let it drain. After the solvent has evaporated, the surfaces will be cleaned and degreased. In case of heavy dirt, wipe the surface.
Attention!
This product is highly flammable!
The product must not be drained into the sewer!
Measures must be taken against static electricity!
Wear appropriate gloves and protective clothing when working!
Complex detergent and lubricant ashless (does not contain metals and their compounds) petrol additive based on synthetic esters for all types of petrol (including two-stroke) and hybrid engines equipped with catalytic converters. Cleans both the fuel system and the exhaust system. Improves the efficiency of catalytic converters by cleaning them WITHOUT DISMANTLING, as well as optimises the operation of oxygen sensors (lambda probes), keeping them clean.
Properties:
– By increasing the combustion temperature and releasing active oxygen in the process, it burns out and removes deposits and impurities in the entire exhaust system, including the catalytic converter and sensors. The result is reduced resistance to exhaust gas movement, optimised composition of the fuel-air mixture and the combustion process, thus increasing engine power and energy conversion efficiency;
– Reduces carbon monoxide formation, opacity and toxicity of exhaust gases, increases the life of catalytic converters, oxygen sensors, spark plugs, injectors and the engine as a whole. This eliminates the most common engine problems leading to “Check Engine” indications and reduces maintenance and repair costs;
– Ensures lubrication of the entire fuel system and cleaning of its individual elements from soot and deposits of all kinds (varnish, resins, etc.), especially from all types of injectors and carburettors, spraying nozzles, fuel pumps, intake valves and the combustion chamber, as well as avoids formation of new deposits thanks to the contained esters and special detergents. Reduces caking of piston rings, which prevents them from getting stuck. All this reduces excessive fuel and oil consumption;
– The strong and resistant oil film formed during the application of the additive significantly reduces wear of all fuel system friction couples and prevents corrosion of its elements, thereby increasing its service life, as well as reducing the wear of cylinders, pistons and piston rings;
– Eliminates problems with starting, restores uniformity of idling speed;
– Compatible with all construction materials;
– Ideal for vehicles operated in urban traffic.
Application: For maximum effective cleaning add in a ratio of 450 ml per 30 L of fuel (1:60) to the fuel tank; to prevent impurities add in a ratio of 1:100.
Anticor Schwarz is a high – quality anti-corrosion and anti-graveling agent in the form of an aerosol based on synthetic resins and rubbers. It is intended for processing of external and internal surfaces of a car body, a bottom, wheel arches, wings, aprons, lower surfaces of thresholds of cars, etc. It is suitable for processing the internal surfaces of the hood, doors, and body amplifiers. For professional body repairs, it is used to protect welds from the inside of panels, protect the internal surfaces of new body panels, as well as to process fenders, doors, aprons, hoods, trunks, etc. before installing on the car.
Properties:
– Reliably protects the body from the negative effects of road salt and deicing reagents, all types of atmospheric effects, corrosion, protects from scratches caused by road surface particles (gravel, crushed stone, etc.);
– Has passivizing properties, significantly slowing down the corrosion process that has already begun;
– Forms a strong, smooth, indelible elastic film with ticostropic properties (can be applied in a thick layer without forming smudges and self-leveling, and scratches on it are prone to self-tightening), resistant to mechanical influences, to moisture, salts, acids and alkalis after drying. Does not chip or wear during operation;
Effectively penetrates into the smallest crevices, displacing water from cracks, crevices and joints between the body panels forms a waterproof layer;
– Has excellent adhesion – holds securely even on smooth, non-porous surfaces. It does not lose its adhesive properties at extremely high temperatures – it does not peel off and is securely held on a heated surface;
– Neutral to metals, plastics, rubbers and paint coatings;
– Resistant to extremely low temperatures, retains plasticity and does not crack;
– It has sound-proof and anti-vibration properties, significantly reducing road noise and vibrations of body elements, thereby increasing the comfort of driving;
– Dry quickly. The declared properties are acquired after complete drying.
Application: before applying the product, the surface must be thoroughly cleaned of rust, dirt and dust, grease, oil and other organic contaminants. For degreasing, we recommend using 9691 MANNOL Brake Cleaner. For best results, it is recommended to apply the product at room temperature.
Shake the balloon well until the balloon inside is released and you can hear its sound. Then continue to shake the balloon for another minute. Hold it upright when spraying and spray in a layer of up to 1.5 mm at a distance of about 20-30 cm from the surface. Resistance to abrasion and corrosion increases with the thickness of the coating. For this reason, the spray process should be repeated once or twice after a short (1-2 minutes) drying time. To obtain a uniform coating and not to leave untreated areas, the spray must be carried out crosswise. The coating is not subject to further staining.
Depending on the thickness of the layer and weather conditions, the car is ready to move again in about 2 hours. Final drying takes 12-24 hours.
Attention! After application, clean the valve on the cylinder by spraying head down until only the propellant gas is released!
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. Privacy PolicyAccept
Reviews
There are no reviews yet.