Chain Cleaner – cleaner of driving chains of motor vehicles and its individual parts in the form of aerosol.
Suitable for all types of chains (O-ring, X-ring, W-ring).
Properties:
– Due to the high content of active substances, it quickly, effectively and carefully cleans and degreases chains from old grease, dirt, dust, sand and other road contaminants;
– Specially selected solvents effectively dissolve and clean the old dried and hardened residues of petroleum products in the form of resin and varnish;
– Has excellent solvent properties and easily penetrates all gaps in the chain;
– Quickly and completely evaporates without damaging the oil seals;
– It is recommended to use before applying fresh 7901 MANNOL Chain Lube.
Application: Place a cloth or cardboard under the parts to be cleaned. Shake the balloon and spray the product liberally several times and let it drain. After evaporation (approximately 10 minutes), the chain becomes clean and fat-free, prepared for applying 7901 MANNOL Chain Lube.
Attention: the product can aggressively affect rubbers, polymer materials and paint coatings – check their compatibility before using.
Motor Cleaner is a detergent for cleaning and care of the engine compartment of the vehicle. Quickly, efficiently and carefully removes most of the typical engine compartment dirt: oils, residues of evaporated and burnt technical fluids, road dirt and dust, road reagents, etc. It has a high cleaning capacity. A clean engine is less likely to overheat.
– Has an increased solvent capacity and active cleaning properties;
– High-viscosity concentration allows components to remain on vertical surfaces, providing excellent cleaning of complex contaminants in all dimensions;
– Neutral in relation to coatings made of chrome, nickel, zinc, etc., as well as to the surfaces of ferrous and non-ferrous (aluminum, bronze, brass, etc.) metals and alloys. It can be aggressive towards certain types of plastics, rubbers and paint coatings;
– Further prevents oxidation, cracking and loss of properties of rubber and plastic parts of the engine under the aggressive influence of pollution and the environment, prevents oxidation of electrical connections, reduces the risk of short circuits, prevents fire of electrical wiring;
– Can be used for cleaning various units of cars, motorcycles, trucks, tractors and other agricultural, garden and construction equipment, as well as water equipment: chassis, filters, pumps, auto and motorcycle-free drive chains, etc. , as well as various inventory and working tools;
– It is recommended to use at the end of the “dirty” season, before and after engine, suspension or transmission repairs, as well as during pre-sale preparation of the car.
Application: Spray the product on the parts to be cleaned from a distance of 15-20 cm, holding the container vertically. Leave to act for 3-5 minutes, depending on the degree of contamination. Wipe with a brush or sponge, and then rinse with water. Repeat the procedure if necessary. Before applying, try the cleaner on a small inconspicuous area to find out possible reactions with different materials.
Chain Lube – fully synthetic white lubricant in the form of an aerosol for high-load and high-speed drive chains of motorcycles, ATVs, scooters and other motor vehicles, as well as bicycles. Suitable for all types of chains (O-ring, X-ring, W-ring).
Properties:
– It has increased stickiness and holds well on the fastest moving chains under the action of centrifugal forces, providing reliable lubrication in all modes;
– Unique additive package and contained micro – ceramic elements-friction modifiers provide excellent anti-friction and anti-wear properties;
– Has good water resistance, does not wash off with hot water when washing equipment;
– Smoothly cares for chain seals of any cross-section (O-ring, X-ring, W-ring);
– Resistant to low ambient temperatures and high (up to 260 °C) operating temperatures;
– Reliably protects chains from corrosion;
– Prevents chains from stretching, extending their service life;
– Neutral to rubbers, plastics and paint coatings.
Application: before applying 7901 MANNOL Chain Lube, it is recommended to clean the chain with 7904 MANNOL Chain Cleaner. Spray the grease on the chain. After evaporation of the solvent (5-10 minutes), the lubricant acquires its final properties – the final consistency and the required adhesion.
Anticor is a high – quality anti-corrosion and anti-gravel agent in the form of a liquid based on synthetic resins and rubbers. It is intended for processing of external and internal surfaces of a car body, a bottom, wheel arches, wings, aprons, lower surfaces of thresholds of cars, etc. It is suitable for processing the internal surfaces of the hood, doors, and body amplifiers. For professional body repairs, it is used to protect welds from inside of panels, protect the internal surfaces of new body panels, as well as to process fenders, doors, aprons, hoods, trunks, etc. before installing on the car.
Properties:
– Reliably protects the body from the negative effects of road salt and deicing reagents, all types of atmospheric effects, corrosion, protects from scratches caused by road surface particles (gravel, crushed stone, etc.);
– Has passivation properties, significantly slowing down the corrosion process that has already begun;
– Forms a strong, smooth, indelible elastic film with ticostropic properties (can be applied in a thick layer without forming smudges and self-leveling, and scratches on it are prone to self-tightening), resistant to mechanical influences, to moisture, salts, acids and alkalis after drying. Does not chip or wear during operation;
Effectively penetrates into the smallest crevices, displacing water from cracks, crevices and joints between the body panels, forms a waterproof layer;
– Has excellent adhesion – holds securely even on smooth, non-porous surfaces. It does not lose its adhesive properties at extremely high temperatures – it does not peel off and is securely held on a heated surface;
– Neutral to metals, plastics, rubbers and paint coatings;
– Resistant to extremely low temperatures, retains plasticity and does not crack;
– It has sound-proof and anti-vibration properties, significantly reducing road noise and vibrations of body elements, thereby increasing the comfort of driving;
– Dry quickly. The declared properties are acquired after complete drying.
Application: before applying the product, the surface must be thoroughly cleaned of rust, dirt and dust, grease, oil and other organic contaminants. For degreasing, we recommend using 9691 MANNOL Brake Cleaner. For best results, it is recommended to apply the product at room temperature.
The product is applied using a spray gun with a compressor at a pressure of 2 to 8 bar (depending on the desired fineness of the spray). Shake the balloon well before use. After pouring the product into the spray container, immediately close the balloon, as a film forms very quickly on the surface of the product. Spray with a layer of up to 1.5 mm at a distance of about 20-30 cm from the surface. Resistance to abrasion and corrosion increases with the thickness of the coating. For this reason, the spray process should be repeated once or twice after a short (1-2 minutes) drying time. To obtain a uniform coating and not to leave untreated areas, the spray must be carried out crosswise. The coating is not subject to further staining.
Depending on the thickness of the layer and weather conditions, the car is ready to move again in about 2 hours. Final drying takes 12-24 hours.
Contact Cleaner is a special cleaning agent for fast and effective cleaning and degreasing of dirty and rusted electrical contacts of all types.
Ideal for:
– cleaning of electrical blocks and contacts, electronic circuit boards and terminal blocks, lamp bases, cable lines, communication relays, interrupters, ignition distributors, starters, generators, fuses, etc. in cars;
– plug sockets, clamps, electrical distribution devices, battery contacts in industry and everyday life;
– audio and video equipment, office and commercial electrical equipment – cash registers, electronic scales, scanners, etc.
Properties:
– Quickly, efficiently and carefully cleans electrical contacts and connectors, as well as electronic elements from fat and oil films, oxides, phosphates, dust and other insulating contaminants. Reduces the electrical resistance of the contacts and thereby reduces the power loss of electrical equipment and stabilizes the voltage;
– Displaces moisture, forms a water-repellent film;
– Quickly evaporates without leaving traces and eliminates current leaks and short circuits;
– Provides long-term protection of electrical contacts from oxidation, while maintaining their conductivity;
– Due to its high penetration capacity, it improves the efficiency and reliability of electronic systems and electrical equipment, preventing failures and failures;
– Silicone-free, safe for plastic and rubber parts, as well as for paint coatings;
– Can be used for degreasing metal surfaces.
Application:
Before cleaning, disconnect the electrical circuit. Spray MANNOL Contact Cleaner on dirt and leave for 5-10 minutes to act, depending on the intensity of the contamination. Remove dissolved dirt with a cloth or brush. Remove excess product with a damp cloth. In case of contact with the surface of plastic and lacquered parts, remove the composition with a damp cloth. Before connecting to the electrical circuit, wait 10 minutes for the solvent residue to evaporate.
Specifications : SAE 5W-40 / 5W40 / ACEA A3/B4 / JASO MA2 / API CI-4/SN
Recommendation / OEM Approval : MB 229.3 / MB 226.5 / MB 229.5 / VOLKSWAGEN 502 00 / VOLKSWAGEN 505 00 / PORSCHE A40 / RENAULT RN17 / RENAULT RN0700 / RENAULT RN0710 / BMW LL-01 / BMW LL-98 / PSA B71 2294 / PSA B71 2296 / FIAT 9.55535-M2 / FIAT 9.55535-N2 / FIAT 9.55535-H2 / FIAT 9.55535-Z2 / CHRYSLER MS-10725 / CHRYSLER MS-10850 / CHRYSLER MS-10896 / CHRYSLER MS-12991 / GM LL-A-025 / GM LL-B-025
Product Details
Innovative ester-containing fully synthetic premium engine oil for modern high-performance turbo diesel engines. Developed in accordance with the requirements of the VW group.
Product Properties:
– Ester-technology and synthetic base with an extended range of viscosity-temperature properties ensures efficient operation of the engine in all operating modes: cold start, urban mode, highway mode, as well as under increased load (when driving off-road, uphill, driving with a trailer, maximum load) and at high ambient temperatures;
– Excellent for active driving and does not lose its properties when using fuel of variable quality (with a sulfur content of up to 500 ppm) due to a large reserve of alkaline number (TBN);
– Synthetic ester-containing base in combination with a modern additive package preserves the power parameters of the engine throughout the entire interval between replacements;
– Ester components of the oil provide excellent anti-wear and anti-friction properties due to the exceptional strength of the oil film, which, combined with excellent pump ability, significantly increases the service life of the engine even in “Start-stop” and cold start modes;
– Due to its excellent detergent-dispersing properties and the highest thermal-oxidative stability, it effectively combats all types of deposits and keeps engine parts clean throughout the entire interval between replacements;
– Applicable for gasoline engines.
It is intended for diesel engines (with and without turbocharging) of a wide fleet of cars: passenger cars, light SUVs, minibuses and light trucks of European and other manufacturers, where the viscosity of SAE 5W-40 is required, and the level of performance properties of API CI-4/SN is required. It is recommended for use in engines of VW, Daimler, BMW cars, including those using direct fuel injection or “common rail” technology.
The oil is not suitable for use in heavy trucks and similar vehicles!
Belt Tensioner – means for care of driving belts: quickly, safely and effectively eliminates extraneous sounds (creaking, whistling, etc.) and slipping of belts, cleans them from dirt, removes traces of oils, restores elasticity, protects against drying and cracking. It is used for drive belts of alternators, air conditioners, power steering and other units.
Properties:
– Reduces wear on belts and pulleys, prevents their aging, thereby extending their service life;
– Increases the efficiency of the belt drive;
– Reduces noise during operation of the engine;
– Especially effective for eliminating the slippage of old belts when they can not be replaced or stretched;
– Suitable for V-belts and semi V-belts, not suitable for flat belts;
– For belts made of leather, various fabrics impregnated with rubber or balata, chemical fibers, nylon, polyurethane and other synthetic materials;
– Regular use of the product extends the service life of the belts by 1.5–2 times.
Application:
Stop the belt drive. Spray a small amount of the product from a distance of approximately 20 cm on the pulley under the side surfaces of the belt and/or directly on the side surfaces themselves. Turn the belt drive at least one full turn of the belt so that the product is evenly distributed over the belt surface. Repeat the procedure one or more times if you want to achieve a greater thickness of the protective layer. After applying the last layer leave to act for 10 minutes before starting the engine again.
Complex detergent and lubricant ashless (does not contain metals and their compounds) petrol additive based on synthetic esters for all types of petrol (including two-stroke) and hybrid engines equipped with catalytic converters. Cleans both the fuel system and the exhaust system. Improves the efficiency of catalytic converters by cleaning them WITHOUT DISMANTLING, as well as optimises the operation of oxygen sensors (lambda probes), keeping them clean.
Properties:
– By increasing the combustion temperature and releasing active oxygen in the process, it burns out and removes deposits and impurities in the entire exhaust system, including the catalytic converter and sensors. The result is reduced resistance to exhaust gas movement, optimised composition of the fuel-air mixture and the combustion process, thus increasing engine power and energy conversion efficiency;
– Reduces carbon monoxide formation, opacity and toxicity of exhaust gases, increases the life of catalytic converters, oxygen sensors, spark plugs, injectors and the engine as a whole. This eliminates the most common engine problems leading to “Check Engine” indications and reduces maintenance and repair costs;
– Ensures lubrication of the entire fuel system and cleaning of its individual elements from soot and deposits of all kinds (varnish, resins, etc.), especially from all types of injectors and carburettors, spraying nozzles, fuel pumps, intake valves and the combustion chamber, as well as avoids formation of new deposits thanks to the contained esters and special detergents. Reduces caking of piston rings, which prevents them from getting stuck. All this reduces excessive fuel and oil consumption;
– The strong and resistant oil film formed during the application of the additive significantly reduces wear of all fuel system friction couples and prevents corrosion of its elements, thereby increasing its service life, as well as reducing the wear of cylinders, pistons and piston rings;
– Eliminates problems with starting, restores uniformity of idling speed;
– Compatible with all construction materials;
– Ideal for vehicles operated in urban traffic.
Application: For maximum effective cleaning add in a ratio of 450 ml per 30 L of fuel (1:60) to the fuel tank; to prevent impurities add in a ratio of 1:100.
Air Filter Oil-special ultra-sticky impregnation for low-resistance air filters (HIGH-FLOW AIR FILTER) – in common language use «zero-it” or “zero-resistance filters”. It is suitable for use in all 2-stroke and 4-stroke motorcycles and scooters with air-and water-cooled engines, as well as in any other equipment in which such filters are installed normally or as tuning details.
Properties:
– Provides maximum air supply, increasing engine power;
– Reliably holds dust, dirt and sand in the most extreme conditions. Reduces wear and extends the oil change interval. Eliminates engine damage caused by contamination, extends its life and reduces maintenance and repair costs;
– Provides excellent adhesive properties of the filter, so that it effectively detains even the smallest dust particles, while it is securely held on the surface of the filter elements;
– Recommended for use in Motorsport;
– Colors the filter in tints from pale pink to red, and the color may appear immediately or after a while;
– Completely eliminates the risk of destruction of HIGH-FLOW filters during operation.
Application: Remove the filter. Clean the filter surface from coarse dust and dirt particles by tapping and then using a soft-pile brush. Apply MANNOL Universal Cleaner 9972 on both sides of the filter. Let it soak in. After 10 minutes, rinse the filter in a container of water, then under a low stream of water. Dry the filter well. Shake the container and spray 9964 MANNOL Air Filter Oil on the filter from a distance of 20-30 cm. Mash the filter to achieve the best penetration of the impregnation into the filter. Let it dry for 15 minutes.
Motor Kaltreiniger – highly effective detergent for cleaning and maintenance of the engine compartment of the car. Quickly, efficiently and carefully removes any contamination of the engine compartment: oil, residues of evaporated and burnt technical fluids, road dirt and dust, road reagents, etc. Softens and dissolves the most difficult to remove and old dirt. A clean engine is less likely to overheat.
– Has an increased solvent capacity and active cleaning properties;
– Active foam stays on vertical surfaces for a long time, providing excellent cleaning of complex dirt in all dimensions;
– Neutral in relation to plastic, rubber, paint coatings, chrome, nickel, zinc, etc., as well as to the surfaces of ferrous and non-ferrous (aluminum, bronze, brass, etc.) metals and alloys;
– Further prevents oxidation, cracking and loss of properties of rubber and plastic parts of the engine under the aggressive influence of pollution and the environment, prevents oxidation of electrical connections, reduces the risk of short circuits, prevents fire of electrical wiring;
– Can be used for cleaning various aggregates of cars, motorcycles, trucks, tractors and other agricultural and construction equipment, as well as water equipment: chassis, filters, pumps, tools, auto and motorcycle drive chains of all types, garden equipment and tools;
– It is recommended to use at the end of the “dirty” season, before and after engine, suspension or transmission repairs, as well as during pre-sale preparation of the car;
– Can be used for cleaning concrete floors from oil.
Application: Spray on the parts to be cleaned from a distance of 20-30 cm and leave to act for 10-20 minutes, depending on the degree of contamination. Then rinse thoroughly with a strong stream of water.
Rust Dissolver is a fast – penetrating and fast-acting rust dissolving and removing agent with excellent anti-friction and water-repellent properties. It allows you to quickly and safely mount and dismantle hardware of all types, as well as lubricates and protects various movable joints from corrosion: door locks and hinges; levers for driving carburetor dampers; telescopic antennas; fasteners for body and chassis elements, etc. Contains substances which gradually release, during the operation, the molybdenum disulfide.
Properties:
– Thanks to the presence of fast-penetrating solvents in its composition, it instantly frees threaded connections from rust, oxides and dirt, which greatly facilitates their dismantling;
– Has good anti-corrosion properties, prevents formation of rust and oxides in the future. Forms a strong waterproof and heat-resistant protective coating;
– Improves the adhesion of the subsequent coating to the treated surface;
– The presence of molybdenum disulfide provides excellent anti-friction properties for mobile joints, ensuring their smooth operation, ease of movement and eliminating creaking for a long time;
– Can be used for drying interrupter-distributors, coils and spark plugs, as it displaces moisture and fuel from their working surfaces, helping to start damp engines and electrical appliances;
– Neutral to metal, plastic, rubber and paint surfaces;
– Can be used in household, service stations, industry and agriculture.
Application: Shake the balloon well before use. Spray on a rusty surface from a distance of approximately 20 cm and let it soak in for 30 minutes. If necessary, wipe the surface with a piece of cloth to remove any remaining rust and dirt.
Carburetor Cleaner – highly effective carburetor cleaner without dismantling it. Quickly, carefully and effectively cleans throttle and air dampers, diffusers, jets and all other available internal surfaces of carburetors, as well as their external surfaces. Applicable to all two – or four-stroke gasoline engines, with or without catalytic converters.
Properties:
– It is a mixture of highly effective organic solvents. Does not contain acetone;
– Completely dissolves and removes all typical carburetor contaminants of various origins;
– Does not clog the engine components located behind the carburetor: valves, combustion chamber, etc.;
– Stabilizes idle speed, facilitates cold start, improves engine acceleration;
– Optimizes the operation of the intake system by cleaning and lubricating its moving parts;
– The product contains substances that are aggressive to paint surfaces and plastics;
– Reduces fuel consumption (up to 5%) and exhaust gas toxicity;
– Applicable for cleaning motorcycle chains, timing chains, clutch parts, oil pumps, gears, crankshafts and other unpainted metal components and engine parts.
Application. Turn off the engine and remove the air filter. You need to get direct access to the throttle. Spray the product on all internal surfaces of the carburetor located in the access area, as well as, if necessary, on external surfaces. Let them dry. Replace the air filter in its original position. It is advisable to replace it at the same time. Turn on the engine and let it run at medium speed, and you can already start driving. You can also let the engine run at idle for 20 seconds at 2000 rpm, so that the remaining dirt in the injection system can burn.
If the engine allows, i.e. can maintain a stable speed when the air intake is disconnected, then cleaning can be performed when the engine is turned on. If this doesn’t work, contact the service center to find out how to do it. Sometimes it is enough to turn off the air flow meter. When the engine is running, the cleaning process is significantly intensified. At the same time, do not allow the product to get on the air flow meter and painted parts.
DPF Regenerator & Flush Fluid – a professional set of tools for gentle cleaning and restoring the efficiency of diesel particulate filters (DPF) without dismantling them. Suitable for all diesel engines, both naturally aspirated and turbocharged, equipped with these systems. Applicable for diesel engines equipped and not equipped with automatic regeneration systems for diesel particulate filters. Suitable for all DPF’s. The product is applied to the particulate filter using a sprayer with a compressor.
Properties:
– 9995 DPF Regenerator starts the process of regeneration of the particulate filter. Promotes complete burning of the accumulated soot, loosening it and acting as a combustion catalyst. Dissolves and removes unburned dirt from the pores of the particulate filter;
– Especially effective for vehicles operating in urban mode and in the cold season;
– Restores the full capacity of the particulate filter, and the 9996 DPF Flush Fluid washes out all the dissolved residues of the 9995 DPF Regenerator;
– Restores the original engine power by reducing the hydrodynamic resistance of the filter. Save fuel;
– Neutral low-ash formula. It evaporates without a trace and is removed from the filter.
– Extends the service life of the particulate filter and reduces the cost of operating the car. Regular use may eliminate the need to replace the DPF altogether;
– Reduces the toxicity of exhaust gases.
1. Stage with the use of DPF Regenerator 9995: Stop the engine. Cool the diesel particulate filter to less than 40 °C. Pour the entire amount of the product into the spray container. Remove one of the particulate filter sensors (pressure or temperature). Insert the spray gun into the orifice. Spray the entire volume of the product in the particulate filter at a pressure of 4 BAR. Leave to act for 20 minutes. Replace the sensor. Place the container under the exhaust pipe to collect dirt. Turn on the engine and let it run at high speed (approximately 3000 rpm) for 5 minutes, while the exhaust pipe may leak dirty black liquid.
Stop the engine. Cool the diesel particulate filter to less than 40 °C.
2. Stage with application of washing liquid 9996 DPF Flush Fluid: Pour the entire amount of the product into the spray container. Remove one of the particulate filter sensors (pressure or temperature). Insert the spray gun into the orifice. Spray the entire volume of the product in the direction of the particulate filter at a pressure of 4 BAR. Leave to act for 1-2 minutes. Insert the sensor into place. Turn on the engine and let it run at 2000 – 2500 rpm for 5 to 15 minutes until the product completely evaporates from the filter. During the cleaning process, foam flakes may escape from the exhaust pipe. Stopping the foam output indicates complete evaporation of the product.
After cleaning is complete, you need to drive for 20-30 minutes on a flat road with an engine speed of about 3000 rpm (it is allowed to let the engine idle for 20-30 minutes with a warm-up to the operating temperature). After that, for the best effect, start the process of forced (manual) regeneration of the particulate filter in accordance with the instructions of the car manufacturer.
To keep the particulate filter clean, use the 9994 MANNOL DPF Filter Cleaner in the future between service periods.
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. Privacy PolicyAccept
Reviews
There are no reviews yet.