-
$111.00
Reifen Doctor-an easy-to-use special spray tool for emergency repair of punctures of chamber and tubeless tires on cast and stamped wheels without dismantling them. The resulting foam quickly and reliably seals punctures and leaks of all types up to 5 mm in diameter by creating a long-lasting self-vulcanizing film when interacting with air. Applicable to all tire sizes of passenger cars, light trucks and trailers. Not applicable for gusts and long slits, or when the tire has slipped off the disk.
Properties:
– Remains in the tire in the active state for a long time and prevents the occurrence of air leaks in the future, including repeated punctures;
– Does not lead to the formation of oxides and rust on the surface of the wheel;
– Does not affect wheel balancing;
– Does not freeze in the coldApplication:
1. If possible, remove the cause of the puncture (nail, self-tapping screw, etc.). Turn the wheel down with the puncture and completely release the remaining air from the tire.
2. In the cold, warm the balloon to a temperature not lower than + 15° C (in a warm cabin, for example), then shake thoroughly.
3. Screw the cylinder connector onto the tire valve.
4. Hold the balloon vertically and inject the entire contents of the balloon into the tire. One cylinder is sufficient for one tire with a rim diameter (landing diameter) of 15′.
5. Inflate the tire to the required pressure. In order for the foam to be evenly distributed inside the tire and reliably seal the punctures, it is necessary to drive at an average speed of 70 km/h 10-15 km.
6. As soon as possible, contact the service Station for professional tire repair, until then, regularly monitor the air pressure in the tire.Note: Not suitable for use in direct measurement tire pressure monitoring systems (TPMS).
-
$111.00
Navy blue roll-up banner with a MANNOL logo.
-
$111.00
RTV BLUE SEALANT is a sealant that hardens at room temperature. Extremely resistant to extreme temperatures. Creates a reliable seal that does not crack, shrink or shift under the influence of sudden temperature changes. Replaces o-rings, washers, and asbestos, rubber, felt, paper, cork, and metal seals. It can be effectively used for repair of: valve guide bushings, oil pans, thermostat housings, pipes, hoses, and other flexible connections. Resistant to lubricants, coolants, gasoline, kerosene, water, acids and alkalis. Easy to apply and remains flexible. The surface to be treated must be degreased.
Operating temperature range: -40 °C to + 230 °C.
Store the sealant in cool and dry conditions in tightly closed original packaging.
It retains its strength for at least two years from the date of production. -
$111.00
Rust Dissolver is a fast – penetrating and fast-acting rust dissolving and removing agent with excellent anti-friction and water-repellent properties. It allows you to quickly and safely mount and dismantle hardware of all types, as well as lubricates and protects various movable joints from corrosion: door locks and hinges; levers for driving carburetor dampers; telescopic antennas; fasteners for body and chassis elements, etc. Contains substances which gradually release, during the operation, the molybdenum disulfide.
Properties:
– Thanks to the presence of fast-penetrating solvents in its composition, it instantly frees threaded connections from rust, oxides and dirt, which greatly facilitates their dismantling;
– Has good anti-corrosion properties, prevents formation of rust and oxides in the future. Forms a strong waterproof and heat-resistant protective coating;
– Improves the adhesion of the subsequent coating to the treated surface;
– The presence of molybdenum disulfide provides excellent anti-friction properties for mobile joints, ensuring their smooth operation, ease of movement and eliminating creaking for a long time;
– Can be used for drying interrupter-distributors, coils and spark plugs, as it displaces moisture and fuel from their working surfaces, helping to start damp engines and electrical appliances;
– Neutral to metal, plastic, rubber and paint surfaces;
– Can be used in household, service stations, industry and agriculture.Application: Shake the balloon well before use. Spray on a rusty surface from a distance of approximately 20 cm and let it soak in for 30 minutes. If necessary, wipe the surface with a piece of cloth to remove any remaining rust and dirt.
Volume: 450 ml
-
$111.00
Code : MN8112
Specifications : SAE 140 / API GL-4/GL-5
Recommendation / OEM Approval :
Product Details
A mineral simple-composition gear oil for mild operating conditions (low loads and sliding velocities).
It may be recommended for the lubrication of accessory equipment to be installed in special vehicles (reducers in autocranes, mechanisms on garbage trucks, side lifting components, etc.) when operating at temperatures no lower than 0 °С. -
$111.00
Code : MN7409
Specifications : SAE 40 / API CH-4/SJ
Recommendation / OEM Approval :
Product Details
A high-efficiency monograde mineral engine oil for heavy-load diesel-powered engines with and without a turbocharger operating under harsh conditions at ambient temperatures more than -20 °C.
Product properties:
– Due to the absence of viscosifiers, it is less susceptible to destruction and ageing than analogues all-season oils, it has an extended expected life which, when combined with a low evaporation ability that reduces oil consumption through burning, allows using it in engines with an extended oil replacement age;
– A highest-quality mineral base and thoroughly selected additives ensure good antifriction and antiwear properties that significantly extend the expected life of the equipment in comparison with oil analogues in all, even the most extreme, operation modes;
– In contrast with analogues, it has an enhanced thermo-oxidising stability due to natural antioxidants that, when combined with good cleaning-dispersing properties that reduce the formation of carbon deposits and lacquer, prevent the formation of deposits of all types and maintain engine parts clean throughout the entire time between replacements;
– It has fair low-temperature properties;
– It effectively protects engine parts against all types of corrosion;
– It may be used when operating on fuel with an increased sulphur content.It is meant for high-load diesel-powered engines of trucks, construction, mining and agricultural equipment, boats, locomotives, as well as stationary equipment. It is suitable for retro-vehicles.
It may be used as hydraulic oil in hydraulic systems including the ones that are combined with mechanic gearboxes or torque converters if the manufacturer requires the use of an engine oil of a specific-grade viscosity in these subsystems.
-
$111.00
Code : MN7407
Specifications : SAE 50 / API CH-4
Recommendation / OEM Approval :
Product Details
A high-efficiency monograde mineral engine oil for heavy-load diesel-powered engines with and without a turbocharger operating under very harsh conditions at ambient temperatures more than -15 °C.
Product properties:
– Due to the absence of viscosifiers, it is less susceptible to destruction and ageing than analogues all-season oils, it has an extended expected life which, when combined with a low evaporation ability that reduces oil consumption through burning, allows using it in engines with an extended oil replacement age;
– A highest-quality mineral base and thoroughly selected additives ensure good antifriction and antiwear properties that significantly extend the expected life of the equipment in comparison with oil analogues in all, even the most extreme, operation modes;
– In contrast with analogues, it has an enhanced thermo-oxidising stability due to natural antioxidants that, when combined with good cleaning-dispersing properties that reduce the formation of carbon deposits and lacquer, prevent the formation of deposits of all types and maintain engine parts clean throughout the entire time between replacements;
– It has fair low-temperature properties;
– It effectively protects engine parts against all types of corrosion;
– It may be used when operating on fuel with an increased sulphur content.It is meant for high-load diesel-powered engines of trucks, construction, mining and agricultural equipment, boats, locomotives, as well as stationary equipment. It is suitable for retro-vehicles.
It may be used as hydraulic oil in hydraulic systems including the ones that are combined with mechanic gearboxes or torque converters if the manufacturer requires the use of an engine oil of a specific-grade viscosity in these subsystems.
-
$111.00
Code : MN7408
Specifications : SAE 60 / API CH-4
Recommendation / OEM Approval :
Product Details
A high-efficiency monograde mineral engine oil for heavy-load diesel-powered engines with and without a turbocharger operating under extra-harsh conditions at ambient temperatures more than -15 °C.
Product properties:
– Due to the absence of viscosifiers, it is less susceptible to destruction and ageing than analogues all-season oils, it has an extended expected life which, when combined with a low evaporation ability that reduces oil consumption through burning, allows using it in engines with an extended oil replacement age;
– A highest-quality mineral base and thoroughly selected additives ensure good antifriction and antiwear properties that significantly extend the expected life of the equipment in comparison with oil analogues in all, even the most extreme, operation modes;
– In contrast with analogues, it has an enhanced thermo-oxidising stability due to natural antioxidants that, when combined with good cleaning-dispersing properties that reduce the formation of carbon deposits and lacquer, prevent the formation of deposits of all types and maintain engine parts clean throughout the entire time between replacements;
– It has fair low-temperature properties;
– It effectively protects engine parts against all types of corrosion;
– It may be used when operating on fuel with an increased sulphur content.It is meant for high-load diesel-powered engines of trucks, construction, mining and agricultural equipment, boats, locomotives, as well as stationary equipment. It is suitable for retro-vehicles.
It may be used as hydraulic oil in hydraulic systems including the ones that are combined with mechanic gearboxes or torque converters if the manufacturer requires the use of an engine oil of a specific-grade viscosity in these subsystems.
-
$111.00
Code : MN8113
Specifications : SAE 90 / API GL-4/GL-5
Recommendation / OEM Approval :
Product Details
A mineral simple-composition gear oil for mild operating conditions (low loads and sliding velocities).
It may be recommended for the lubrication of accessory equipment to be installed in special vehicles (reducers in autocranes, mechanisms of garbage trucks, side lifting components, etc.) when operating at temperatures no lower than – 18 °С. -
$111.00
Code : MN7404
Specifications : SAE 20W-50 / 20W50 / API SN/CH-4
Recommendation / OEM Approval :
Product Details
Universal economy-class engine oil, which is a mixture of synthetic components and a high purity mineral base, for modern highly accelerated petrol and diesel engines with and without a turbocharger used in difficult operating conditions and engines with a very high mileage used in various operating conditions.
Product properties:
– Reduces the leakage probability and maintains the required oil pressure even for engines with a high mileage due to stable viscosity and excellent compatibility with sealing materials;
– Low volatility decreases oil consumption through burning;
– A thoroughly balanced additive package ensures an efficient service of an engine in all modes of operation: cold start, increased load (off-road and uphill driving, towing, driving with maximum load) and in high-temperature ambient conditions;
– Long-lasting oil film effectively protects from wear, reduces friction and prevents corrosion;
– Ensures reliable lubrication of all engine components under all operating conditions;
– Low ash content and good detergent and dispersing properties minimise the soot and carbon formation and keep engine components clean throughout the entire interval between replacements;
– Natural antioxidants effectively resist ageing.Designed for the maximum protection of modern petrol and diesel engines of a wide car fleet (passenger cars, light SUVs, minibuses and light trucks) from Russian, European and other manufacturers.
The oil is not suitable for use in heavy trucks and similar vehicles! -
$111.00
MANNOL Scheiben Reiniger 1:100 is a highly efficient super – concentrated summer wiper for use in the washer tank.
Properties:
– Effectively removes dirt, insects, oil stains, silicone film and other heavy dirt from windows and headlights;
– Quickly provides transparency of the windscreen, increasing driving safety;
– Has a pleasant citrus smell
– Does not leave stains and streaks on the glass;
– Free of phosphates, biologically neutral;
– Chemically neutral to rubbers, plastics and paint coatings.Application: dilute with water in a ratio of 1:100 (25 ml per 2.5 liters of water) and pour into the washer tank.
-
$111.00
Scheiben-Reiniger (-70 °C) is a highly efficient concentrated winter wiper for use in the washer tank.
Properties:
– Effectively removes dirt, road de-icing agents, oil stains, silicone film and other heavy dirt from windows and headlights;
– Guaranteed to remove ice down to -70 °C;
– Quickly and easily provides transparency of the windscreen, increasing driving safety. Suitable for all types of windshields: triplex, securiflex, etc. with or without heating, as well as for rear and side windows (tempered glass) and headlights made of any material;
– Has a pleasant citrus smell
– Does not leave stains and streaks on the glass;
– Free of phosphates, biologically neutral;
– Chemically neutral to rubbers, plastics and paint coatings.Application: dilute with water in a ratio of 1:1 (1 liter of product per 1 liter of water), while the solution will work down to – 20 °C, and pour into the washer tank. When diluted 1:2 (1 liter of the product per 2 liters of water), the solution will remain functional down to – 10 °C. It can be used in a concentrated form.
-
$111.00
Schleifpaste Profi Set is a set of professional diatomite abrasive pastes for manual and MECHANICAL polishing of paint coatings. Pastes differ in the grain size of the abrasives. MANNOL Schleifpaste No. 1 removes deep scratches, damaged, oxidized or dull top layers of paint due to the large abrasive grains contained in it. It allows you to easily remove smudges and stains of lacquers and paints during the restoration of the body, as well as adjust the color shades during partial painting. MANNOL Schleifpaste No. 2 removes small scratches, minor defects in paint coatings and solidified residues of petroleum products due to the micro abrasive components contained. It easily removes excess varnish after painting the body, facilitates deep cleaning of the surface, removes rust and aggressive substances from the micro cracks of the paintwork and individual chrome parts. Sizes of abrasive particles: MANNOL Schleif Paste No. 1 – 75 microns, MANNOL Schleif Paste No. 2 – 3 microns.
Application:
Clean the surfaces to be treated. RUB MANNOL Schleif paste No. 1 on small areas with a cloth or sponge, with the necessary pressure, Until the damaged and oxidized layers of the previous coating, rust, oxides, dirt and scratches are removed. For a mirror-like finish, apply MANNOL Schleif Paste No. 2 liberally to the surface using the supplied wet cloth and Polish it, then rinse it off. -
$111.00
Highly foaming shampoo concentrate with the highest washing and cleaning action for manual contact car wash.
Product properties:
– Forms very rich active foam;
– Effectively removes all types of stains and dirt: dusty fuel, oil, fat, soot, insect residues, etc. due to its excellent splitting properties;
– Suitable for washing glass;
– Easily washed off with water without leaving streaks and smudges and whitish spots;
– Leaves a great glossy effect;
– Can be diluted with warm and cold water. Effective even when using hard water;
– Has the smell of sea breeze;
– Does not contain phosphates;
– Biodegradable, environmentally friendly product that meets all EU requirements.Compatibility: Safe for paint surfaces, plastics and rubber products.
Application: Remove in advance large dirt with a strong stream of water. To prepare the working solution, the concentrate must be diluted with water in a ratio from 1: 10 to 1: 20, depending on the degree of contamination. Apply the mixture with a sponge on the surface to be cleaned and distribute it over it. Then rinse thoroughly with water and wipe with suede. -
$111.00
-
$111.00
The Latest development – a lubricating additive in gasoline. It is intended for all types of fuel systems of gasoline engines, first of all – for engines with direct fuel injection into cylinders. In diesel engines, such a power system was introduced earlier and showed its effectiveness, but also found a number of problems related to the lack of quality of lubrication of moving metal parts of the fuel system, and especially the high pressure fuel pump. We present a multifunctional complex for gasoline fuel. This balanced package of additives meets the most modern requirements, is compatible with any gasoline fuel, is easily mixed with it and completely dissolves, and is guaranteed to improve any commercial gasoline fuel, even if it contains ethanol, giving it best consumer properties, transferring it to the rank of the so-called "brand" fuel. When testing the lubricity of commercial gasoline AI-95, a more than twofold decrease in the diameter of the wear spot was recorded when only 0.1% of the additive was introduced into the fuel (1 liter of additive per 1000 liters of gasoline). In addition, the additive has a friction modifier and an ignition promoter, which increases the completeness of fuel combustion and reduces the formation of carbon deposits in the combustion chamber. With regular use of the additive, engine performance improves and significant fuel savings occur (2-5%)
Properties:
– Guaranteed to improve the lubricity of gasoline, protects the entire fuel system and its individual elements from corrosion, especially: all types of injectors, carburetor jets, fuel pumps, intake valves and the combustion chamber, prevents excessive fuel and oil consumption;
– All other things being equal, it increases the engine power and acceleration of the car, including by improving the lubricating properties of gasoline, reducing friction in the cylinder zones and ensuring optimal fuel dispersion;
– Reducing carbon formation, smoke and toxicity, increases the life of spark plugs, oxygen sensors, catalysts, injectors (injectors) and the engine as a whole;
– Forms a stable oil film on the parts of the fuel system, which prevents their corrosion;
– The strong and stable oil film formed when using Benzin Ester Additive significantly reduces the wear of all rubbing pairs of the fuel system, thereby increasing its service life, and also reduces the wear of cylinders, pistons and piston rings;
– Eliminates problems with starting, restores the uniformity of idle speed and reduces detonation;
– A clean engine uses less fuel and emits less harmful substances;
– Compatible with all exhaust gas and turbocharging systems;
– Compatible with all construction materials;
– Recommended for preserving the engine when it is idle for a long time.
Application: Add to the tank in the ratio of 50 ml per 50 liters of fuel.
Recommended for regular use.
Shelf life: 5 years from the date of production.
Code : MN7715
Specifications : SAE 5W-30 / 5W30 / API SN / ACEA C3
Recommendation / OEM Approval : MB 229.51 / VOLKSWAGEN TL 52 195 / BMW Longlife-04 / PORSCHE C30 / VOLKSWAGEN 504 00 Approval / VOLKSWAGEN 507 00 Approval
Product Details
Innovative universal premium bi-synthetic engine oil (PAO-based) for modern petrol and diesel engines of VW group cars (including direct injection) with and without turbocharging, including those equipped with pump-injectors (Pumpe-Düse).
Product properties:
– Due to the ester components contained, it has excellent anti-wear, extreme pressure and anti-friction properties, which ensures long and trouble-free operation of the pump-nozzle system and the entire gas distribution mechanism, reducing cam wear;
– Due to its excellent detergent-dispersing properties and high thermal-oxidative stability, it effectively combats all types of deposits and keeps engine parts clean throughout the entire interval between replacements;
– Saves fuel due to optimal anti-friction properties;
– Ester components together with the bi-synthetic base provide a low solidification temperature (-45 °C and below) and guarantee easy low-temperature engine start-up due to exceptional turn ability and pump ability, which significantly reduces engine starting wear;
– It has optimal viscosity over a wide temperature range, which ensures stable operation in all operating modes, including in urban mode and under overload conditions;
– Due to its high thermal-oxidative stability, it effectively resists aging;
– Compatible with all exhaust gas neutralization systems, DPF, TWC, EGR and SCR through the use of Mid SAPS technology;
– Used in engines with extended oil change intervals (Long Life up to 30,000 km) and conventional;
– Suitable for engines running on liquefied natural gas (LNG) and petroleum gas (LPG).
Designed for gasoline and diesel engines of EURO IV and EURO V wide fleet of vehicles (cars, light SUVs, vans and light trucks) of VW imposes additional requirements on motor oils in accordance with the specifications 504.00/507.00 and previous.
The oil is not suitable for use in heavy trucks and similar vehicles!
Code : MN7701
Specifications : SAE 5W-30 / 5W30 / API SN Plus / ACEA C3 / ACEA C2
Recommendation / OEM Approval : VOLKSWAGEN 505.01 / BMW LL-04 / MB 229.52 / MB 229.51 / MB 229.31 / GM dexos2 / PORSCHE C30 / JASO DL-1 / CHRYSLER MS-11106 / FIAT 9.55535-S1 / FIAT 9.55535-S3 / RENAULT RN17 / RENAULT RN0700 / RENAULT RN0710 / PSA B71 2290 / FORD WSS-M2C934-A/B / TOYOTA 08880-83388 / TOYOTA 08880-83389 / MAZDA 183418 / MAZDA 183419 / JAGUAR STJLR.03.5005 / LAND ROVER STJLR.03.5005 / IVECO 18-1811 CLASSE SC1
Product Details
Premium synthese engine oil, specially developed for gasoline and diesel engines of CHEVROLET, OPEL and GM vehicles.
Product properties:
– Ester components provide excellent anti-wear properties due to the exceptional durability of the oil film, which, combined with excellent pumpability, significantly increases engine life even in engines with start-stop systems;
– Effectively saves fuel due to low HTHS viscosity, high fuel efficiency, and unique anti-friction properties;
– Ensures easy and smooth cold start due to excellent crankability and pumpability, which significantly reduces engine wear;
– Maintains optimal viscosity in a wide temperature range and ensures stable engine operation in all operating modes, including engine overloads;
– Synthetic base guarantees low volatility and low oil waste;
– Effectively prevents all types of deposits and keeps engine parts clean throughout the entire interval between replacements due to the excellent washing-dispersing properties and the highest thermal-oxidative stability;
– Resists ageing due to the high thermal-oxidative stability, increasing the oil change interval;
– Compatible with all exhaust gas aftertreatment systems including DPF, TWC, EGR and SCR thanks to the low SAPS technology;
– Suits engines running on liquefied natural (LNG) and petroleum (LPG) gas.
Developed for cars and light trucks of European and other manufacturers that meet EURO III, IV, V standards and are equipped with catalysts (TWC) and particulate filters (DFP/FAP). Works best in engines where SAE 5W-30 oil, which also meets GM dexos2 or older specifications such as GM LL A025/B025, is recommended.
Code : MN4112
Specifications : SAE J1034 / JASO M325
Recommendation / OEM Approval : AFNOR FRANCE NF R15-601 (except for RA) / ASTM USA D3306 / ASTM USA D4656 / ASTM USA D4985 / ASTM USA D6210 / BSI GB BS 6580:2010 / FVV GERMANY Heft R443 / KSM SOUTH KOREA 2142 / MIL BELGIUM BT-PS-606-A / MIL FRANCE DCSEA 615/C / MIL ITALY E/L-1415b / MIL SWEDEN FSD 8704 / NATO S-759 / OENORM AUSTRIA V5123 / UNE SPAIN 26-361-88/1 / ADE / ASTON MARTIN / VOLKSWAGEN TL 774 D / VOLKSWAGEN TL 774 F / BEHR / BERGEN ENGINES 2.13.01 / BMW GS 94000 / BRB BR 637 / CASE NEW HOLLAND MAT 3624 / CATERPILLAR MAK A4.05.09.01 / CHEVROLET / CLAAS / CUMMINS CES 14439 / CUMMINS CES 14603 / CUMMINS IS series N14 / DACIA 41-01-001 / 41-01-001-T / DAF 74002 / DETROIT DIESEL DFS 93K217 / FENDT / FORD WSS-M97B44-D / GREAT WALL / HITACHI / ISUZU / JAGUAR CMR 8229 / JAGUAR STJLR.651.5003 / JENBACHER TA 1000-0201 / JOHN DEERE JDM H5 / KAROSA / KOBELCO / KOMATSU 07.892 (2009) / LAND ROVER STJLR.651.5003 / LEYLAND TRUCKS DW03245403 / LIEBHERR MD1-36-130 / MACK 014 GS 17009 / MAN 324 Typ SNF / MAN B W A S / MAN B W DIESEL AG D36 5600 / MAZDA MEZ MN 121 D / MB 325.3 / MITSUBISHI MHI / MTU MTL 5048 / MWM 0199-99-2091/11
Product Details
A carboxylated (organic – OAT Organic Acid Technology) concentrated antifreeze intended for a year-round use in any modern cooling system for which the use of ethylene-glycol-based antifreeze is recommended.
It ensures a reliable protection of any cooling system.
Product properties:
– It ensures a reliable protection of metals and alloys (brass, copper, alloy-treated steel, cast iron, aluminium) from all forms of corrosion, as well as prevents a high-temperature corrosion of aluminium surfaces of modern engines. It provides sufficient anti-corrosion properties from the concentration as low as 20%;
– It has an exceptional thermal stability. It protects from deposit formation;
– It has excellent heat conductivity properties and a resistance to foam formation;
– It is neutral to inserts and hoses, compatible with all types of rubber and plastic components of a cooling system;
– It has an excellent resistance to hard water and very low corrosion inhibitor depletion rates;
– The highly effective carboxylated additive package (OAT) ensures an exceptional stability of service qualities of the antifreeze throughout the entire service life;
– It does not contain silicates, nitrates, phosphates and amines (the NAP free technology);
– It has an extended service life in cooling systems: of passenger cars – up to 250 thousand km; of commercial vehicles – up to 500 thousand km; of stationary engines – up to 6 years.
It is recommended for engines requiring enhanced heat dissipation: highly accelerated engines, engines with a turbocharger and cooling systems of modern commercial vehicles.
Colour: red.
Service life: no less than 5 years.
Comply with the manufacturer’s instructions provided in the user’s manual!
| Pour point, °C | Mix ratio, % | |
| Coolant fluid ratio | Water ratio | |
| -20 | 35 | 65 |
| -25 | 40 | 60 |
| -29 | 45 | 55 |
| -38 | 50 | 50 |
Code : MN7921
Specifications : SAE 0W-20 / 0W20 / ACEA C5 / API SP (RC)
Recommendation / OEM Approval : MB 229.71 / BMW LL-17FE+ / VOLVO VCC RBS0-2AE (ServiceFill) / OPEL OV0401547 / GM dexos1 Gen2 / GM dexosD / HONDA HTO-06 / GM 6094M / CHRYSLER MS-6395 / CHRYSLER MS-13340 / JAGUAR STJLR.51.5122 / LAND ROVER STJLR.51.5122 / FORD WSS-M2C947-A / FORD WSS-M2C947-B1
Product Details
Innovative energy-saving, low-viscosity bi-synthetic (PAO + esters) premium engine oil for the latest models of turbocharged gasoline engines (multipoint or direct injection) with gasoline particulate filters.
Product properties:
– Due to the unique bi-synthetic base and the esters contained in it, it has excellent anti wear, antifriction and extreme pressure properties, which ensures long and trouble-free operation of all engine systems, including turbo units. Effectively protects the timing chain from wear;
– Eliminates uncontrolled premature ignition of the fuel-air mixture in engines with direct injection (Low Speed Pre Ignition or LSPI);
– Outperforms similar oils of the SN category in terms of detergent and dispersant properties and thermal-oxidative stability, effectively combats all types of deposits and keeps engine parts clean throughout the entire drain interval. Effectively protects against high-temperature deposits on the piston and turbocharger, effectively fights sludge and lacquer formation;
– Outperforms similar SN oils in terms of fuel efficiency due to their unique composition and excellent antifriction properties;
– Bi-synthetic low-viscosity PAO + Ester base guarantees easy low-temperature engine start due to exceptional cranking and pump ability, which significantly reduces engine starting wear;
– Possesses optimal viscosity in a wide temperature range (for engines in which it is recommended), which ensures their stable operation in all operating modes, including overload;
– Due to its high thermo-oxidative stability, it effectively resists aging;
– Fully compatible with all exhaust gas after treatment systems, DPF, TWC, EGR and SCR through the use of Mid SAPS technology;
– Compatible with ethanol-containing fuels;
– It is used in engines with an extended oil change interval (Long Life up to 30,000 km) and conventional ones.
Recommended for use in gasoline engines of the latest generations of European and Japanese car manufacturers, which impose additional requirements for engine oils in accordance with the above standards and specifications.
The oil is not suitable for use in heavy trucks and similar vehicles!
Innovative engine protection agent based on synthetic compound ethers – esters (group V oils) and hexagonal boron nitride microparticles h-BN (white graphite) – anti-wear and anti-friction additive for engine oils without oil bath clutches (friction clutches). It is suitable for all types of engines – diesel and petrol, four-stroke and two-stroke and for all types of oils – mineral, semi-synthetic, synthetic, including those containing ether (ester). Ideal product for tuning and high-performance cars.
It is a stable suspension of graphite-like micro powder in ether.
Ether molecules in the additive are magnetically bound to metal surfaces due to their distinct polarity and form a dense and very stable oil film, while ceramic microparticles smooth out any unevenness of friction surfaces and effectively dissipate heat. This prevents direct contact of metal surfaces and wear of separate parts even under the most extreme operating conditions. Dry friction during cold starts, especially at sub-zero temperatures, is prevented, thus minimising wear during engine start-up.
The boundary layer that forms when the product is applied has the following properties:
– extreme pressure resistance – allowing the engine and/or transmission to operate at increased loads without negative consequences;
– excellent anti-wear and anti-friction properties, which significantly increases the life of the engine and/or transmission unit and significantly reduces fuel consumption and engine noise;
– anti-corrosive and anti-oxidant properties.
The additive gives the oil the following properties:
– it prevents dry friction;
– it reduces evaporation, decreases CO2 emissions and prolongs oil life;
– it improves the thermal-oxidative stability, which increases the resistance to ageing and degradation, thus extending the oil change intervals;
– improves low-temperature properties, making cold starts much easier;
– improves detergent and dispersion properties, preventing deposits of varnish, resins and sludge, which increases the life of the engine and/or transmission and the oil itself.
Compatibility:
– Compatible with all materials, particulate and finest oil filters (for fine filtration): the particle size (no more than 0.5 μm) ensures their free passage through all filters and prevents deposits;
– Compatible with catalytic converters, all types of turbochargers and all injection systems including common rail.
Application: Shake and add to the oil at a ratio of 300 ml per 5 L.
Attention! Not suitable for use in equipment with oil bath clutches (friction clutches).
Code : MN3002
Specifications : SAE J1703/J1704 / ISO 4925 / FMVSS 116 DOT 4 / JIS JAPAN K2233
Recommendation / OEM Approval :
Product Details
Synthetic brake fluid based on polyglycols and esters, containing corrosion and oxidation inhibitors. Designed for hydraulic systems of all traditional brake devices and clutches.
Product properties:
– Contains boric acid, which completely neutralizes water condensate;
– Provides reliable operation of the brake system at any ambient temperature due to the increased boiling point (>245 °C) and excellent low-temperature properties (up to -40 °C);
– Has the highest chemical and thermal stability;
– Offers excellent lubricity and viscosity-temperature properties;
– Neutralizes the formation of vapour bubbles;
– Compatible with elastomers;
– Entirely inactive for the parts of the brake system.
Aggressive to paintwork.
Follow the manufacturer’s instructions in the instruction manual!
Color: colorless / light brown.
Code : MN8207
Specifications : JASO M315, Class 1-A-LV
Recommendation / OEM Approval : AISIN WARNER JWS 3309 / AISIN WARNER JWS 3324 / AISIN WARNER ATF-0T4 / AISIN WARNER ATF-0WS / SATURN Z 000169756 / ALLISON C4 / ALLISON C3 / ALLISON C2 / ALLISON 389 / BENTLEY PY112995PA / CASTROL TE-ML 09 / FORD Mercon LV / FORD ESP-M2C138-CJ / FORD ESP-M2C166-H / FORD XT-10-QLV [LV] / FORD XT-2-QDX [M] / FORD XT-2-QSM [Syn] / FORD XT-5-QM [V] / FORD XT-5-QSM [V Syn] / FORD XT-6-QSP [SP] / FORD XT-8-QAW [Premium] / FORD XT-9- QMM5 [FRN5] / FORD WSS-M2C922-A1 / GM Dex-VI [GMW 16444] / GM Dex [GM 6032M] / GM Dex-B [GM 6032M] / GM Dex-IIC [6137M] / GM Dex-IID [GM 6137M] / GM Dex-IIE [GM 6137M] / GM Dex-IIIF [GM 6297M] / GM Dex-IIIG [GM 6417M] / GM Dex-IIIH [GM N10055] / GM 19 40 700 / GM 19 40 767 / GM 21005966 / GM 88900925 / GM 9985010 / GM 9986195 / GM Type A Suffix A / GM Saturn T-IV Fluid / GM Saturn 22689186 / GM ATF Z1 / GM Saturn 22717466 / GM AW-1 / GM 19256039 / GM ATF WS / GM 88863400 / GM 88863401 / HYUNDAI ATF SP-IV / HYUNDAI ATF RED-1K / HYUNDAI Genuine ATF / HYUNDAI JWS 3314 / HYUNDAI 00232-19023 / HYUNDAI 040000C90SG / HYUNDAI 04500-00140 / HYUNDAI UM040 CH20 Red-1 / HYUNDAI SP / HYUNDAI SP4-M1 / HYUNDAI SPH-IV / HYUNDAI SP-II / HYUNDAI SP-III / HYUNDAI SP-IV / HYUNDAI SP-IV-RR / HYUNDAI WS, spec NWS-9638 / KIA SP-IV / KIA ATF RED-1K / KIA ATF SP-IV / KIA Genuine ATF / KIA JWS 3314 / KIA 00232-19023 / KIA 040000C90SG / KIA 04500-00140 / KIA SP / KIA UM040 CH20 Red-1 / KIA SP4-M1 / KIA SPH-IV / KIA SP-II / KIA SP-III / KIA SP-IV-RR / KIA WS, spec NWS-9638 / TOYOTA ATF WS Lifetime / TOYOTA JWS 3324 / TOYOTA ATF FZ / TOYOTA JWS 3309 / TOYOTA 08886-81015 / TOYOTA Type T, T-II, T-III, T-IV / TOYOTA Type D-II / MB 236.14 / MB A 0019892203 / MB ATF 3403-M115 / MB 236.1 / MB 236.10 / MB 236.11 / MB 236.12 / MB 236.15 / MB 236.2 / MB 236.41 / MB 236.5 / MB 236.8 / NISSAN Matic S / VOLKSWAGEN LT 71141 / VOLKSWAGEN G 052 162 [AG4] / VOLKSWAGEN G 052 533 / VOLKSWAGEN G 052 990 A2 / VOLKSWAGEN G 055 005 A2 / VOLKSWAGEN G 055 025 A2 / VOLKSWAGEN G 055 162 A2 / VOLKSWAGEN G 055 540 A2 / VOLKSWAGEN G 060 162 A2 / VOLKSWAGEN G US 000 162 / NISSAN Fluid A / NISSAN Matic D / NISSAN Matic J / NISSAN Matic K / NISSAN Matic W / NISSAN N402 / NISSAN 999MP-MTJ00P, 999MP-MTS00P / BMW ATF 3+ / BMW ATF4 / BMW ATF6 / BMW ETL-7045 / BMW ETL-7045 E / BMW ETL-8072B / BMW LA 2634 / BMW LT 71141 / BMW M-L12108 / BMW 81 22 9 400 272 / BMW 81 22 9 400 275 / BMW 81 22 9 407 858 / BMW 81 22 9 407 859 / BMW 83 22 0 024 249 / BMW 83 22 0 024 359 / BMW 83 22 0 026 922 / BMW 83 22 0 142 516 / BMW 83 22 0 397 114 / BMW 83 22 0 402 413 / BMW 83 22 0 403 248 / BMW 83 22 0 403 249 / BMW 83 22 2 152 426 / BMW 83 22 2 163 514 / BMW 83 22 2 220 438 / BMW 83 22 2 220 440 / BMW 83 22 2 220 442 / BMW 83 22 2 289 720 / BMW 83 22 2 305 396 / BMW 83 22 2 305 397 / BMW 83 22 2 355 599 / BMW 83 22 2 355 601 / BMW 83 22 7 542 290 / BMW 83 22 9 407 765 / BMW 83 22 9 407 807 / MINI ATF JWS 3309 / MINI 83 22 0 402 413 / FCA ATF+4 / FCA 68171866AA / FCA ATF+3 / FCA ATF+2 / FCA ATF+ / FCA ASRC / FCA 8 & 9 Speed ATF / FCA 68218925AA / FCA 68218925AB / FCA AW-1 / FCA 68092912AA / FCA 68043742AA / FCA Dex-VI / FCA 05127382AA / FCA 05127382 / FCA 68157995AA / FCA 68157995AB / FCA 68333587AA / FCA SP-IV / FCA SP-III / FCA 68171869AA / FCA Type 7176E / FCA Type 9602 / ATF M-1375.4 / ATF M-1375.6 / ATF LA 2634 / ATF L12108 / ATF ETL-7045 E / ATF 3403-M115 / ATF 3100 PL085 / ATF 3353 / ATF 134 / ATF K17 / ATF N402 / DAIHATSU D3-SP / HONDA ATF DW-1 / HONDA 08200-9008 / HONDA ATF Type 3.0 / HONDA 08200-9016-A / HONDA ATF Type 3.1 / HONDA 08200-9017 / HONDA ATF Z1 / HONDA 08200-9001 / HONDA 08200-9001A / ISUZU ATF II / ISUZU ATF III / ISUZU Genuine ATF / ISUZU 08200-9001 / ISUZU SCS / JAGUAR WSS-M2C922-A1 / JAGUAR 02JDE 26444 / JAGUAR Fluid 8432 / JAGUAR JLM 20238 / JAGUAR JLM 20292 / JAGUAR JLM 21044 / JAGUAR K17, Jatco 3100 PL085 / JAGUAR LT 71141 / LAND ROVER ATF N402 / LAND ROVER AW-1, LR0022460: LV / LAND ROVER JWS3309US / LAND ROVER TYK500050 / LAND ROVER LR023288/LR023289 / MAN 339A / MAN 339D / MAN 339F / MASERATI Oil No. 231603 / MAZDA ATF FZ, ATF N-1, ATF S-1 / MAZDA ATF M-5, 0000-23-ATF -M5 / MAZDA F-1 / MAZDA JWS3317 / MAZDA M3 / MAZDA Type T-IV, JWS 3309 / PEUGEOT Z 000169756 / PORSCHE JWS 3309 / PORSCHE 000 043 205 28 / PORSCHE LT 71141 / PORSCHE 000 043 204 63 / PORSCHE 000 043 304 00 / PORSCHE 999 917 547 00 (A2) / PORSCHE 000 043 205 09 / PSA AL4 / 4HP20 / PSA 9730AE / PSA B71 2340 / RENAULT DP-0 / RENAULT Matic D2 / RENAULT SATF-D / Oil No. PL 31493PA / SAAB ATF HP / SAAB JWS 3309 / SAAB 93 160 393 / SAAB 93 165 147 / ROLLS_ROYCE Dex-IIIG / ROLLS_ROYCE T-IV Fluid / ROLLS_ROYCE 22689186 / SSANGYONG DSIH 5M-52 / SSANGYONG DSIH 5M-66 / SUBARU ATF HP / SUBARU ATF-WS / SUBARU K0140Y0700 / SUBARU SOA635040 / SUZUKI ATF 2326 / SUZUKI ATF 2384K / SUZUKI ATF 3314 / SUZUKI ATF 3317 / SUZUKI ATF 5D06 / SUZUKI Matic D / SUZUKI Matic J / SUZUKI Matic S / VOLVO 1161521 / VOLVO 1161621 / VOLVO 1161640 / VOLVO 1161540 / VOLVO 31 256 774 / VOLVO 31 256 775 / VOLVO 97340, AT100 / VOLVO 97341, AT101 / ZF LifeguardFluid 5 (ZF No. S671 090 170) / ZF LifeguardFluid 6 (ZF No. S671 090 255) / ZF LifeguardFluid 8 (ZF No. S671 090 312) / ZF LifeguardFluid 9 (ZF No. AA01.500.001) / ZF TE-ML 05L / ZF TE-ML 11A / ZF TE-ML 11B / ZF TE-ML 21L
Product Details
A universal all-season synthetic transmission fluid (ATF) for automatic gearboxes, hydraulic converters, hydraulic power steering systems, car hydraulic clutches and other hydraulic devices, including the ones operating in heavy-duty conditions in trucks and off-road vehicles. It ensures a flawless operation of an automatic gearbox, guarantees minimal wear, a lasting service life of transmissions and fuel economy. It was developed on the basis of the requirements set by GM and Ford groups.
Product properties:
– The highest-quality low-viscosity synthetic base with a consistent high viscosity index in combination with a multifunctional additive package preserves all its properties in a wide range of temperatures: it ensures good lubricating properties at low (-45 °C and lower) temperatures in winter and ensures a stable oil film under extreme loads and at high temperatures in summer;
– The high-technology combination of additives ensures excellent antifriction properties for gear couplings and superior friction properties for friction elements thus ensuring a significant fuel economy, a continuous, exact and smooth transmission shift in any driving conditions and an extended service life of the automatic gearbox itself and all transmission elements. It ensures a coordinated and smooth operation of clutches. It prevents scuffing;
– It has an exceptional thermal-oxidative and chemical stability and resistance to the high-temperature thermal degradation throughout the entire service life. It allows reducing lacquering, formation of sludge, soot and other carbon deposits, increasing the time between oil changes and ensuring the durability of transmission components thus reducing the equipment maintenance costs;
– It effectively protects metal parts from ferrous and non-ferrous alloys (especially radiators) from corrosion when both in and not in operation; It has a great compatibility with friction coupling materials;
– It effectively resists aeration and foam formation;
– It ensures an excellent compatibility with all sealing materials, prevents them from swelling, hardening and shrinking that allows reducing the costs for spare parts and prevents leakages. It effectively protects fluoroelastomer seals of heavy equipment;
– It reduces noise.
It is recommended for automatic gearboxes of passenger cars requiring the ATF Type Dexron-VI or Dexron-III H/G/F or Dexron-III E or FORD MERCON LV quality oil. It is recommended for use in new 6-speed transmissions of GM, BMW, Land Rover, Jaguar vehicles, as well as 8- and 10-speed transmissions of Aisin vehicles.
Colour: red.
Comply with the manufacturer’s instructions provided in the user’s manual!
Code : MN7919
Specifications : SAE 0W-30 / 0W30 / API SN/SN Plus / API SP / ACEA C2
Recommendation / OEM Approval : ACEA C3 / BMW LL-12FE / MB 229.61 / FORD WSS-M2C950-A / OPEL OV0401547 / PSA B71 2290 / PSA B71 2312
Product Details
Innovative universal bi-synthetic (PAO+esters) premium engine oil for modern petrol and diesel engines with and without turbocharging.
Product properties:
– Exceptional fuel savings obtained due to the reduced HTHS viscosity and optimal antifriction properties;
– A low-viscosity bi-synthetic base (PAO+esters) and a high-efficiency additive package ensure a steady cold start in the harshest conditions thus reducing the startup wear of the engine;
– For turbocharged engines with direct injection the unique oil formula completely nullifies the effect of LSPI (Low Speed Pre-Ignition);
– Due to excellent cleaning-dispersing properties and the highest thermo-oxidising stability, it efficiently fights against all types of deposits (including varnish, sludge and high temperature deposits) and maintains engine and turbocharger separate parts clean during the entire period between the oil changes;
– Ester oil components ensure excellent anti-wear properties due to the exceptional durability of the oil film, which, when combined with excellent pumpability, significantly extends the service life of the engine even in “Start-stop” driving modes. Effectively protects the timing chain against wear;
– Compatible with all exhaust gas aftertreatment systems, DPF, TWC, EGR and SCR by using Mid SAPS technology;
– Used in engines with extended oil change intervals (Long Life up to 30,000 km) as well as in ordinary ones;
– The modern additive package combined with the bi-synthetic base preserves power parameters of the engine throughout the entire interval between oil changes.
Designed for petrol- and diesel-powered engines of MERCEDES-BENZ, FORD, BMW etc. passenger cars, lightweight off-road vehicles and light trucks that impose additional requirements for engine oils in accordance with the listed specifications and the preceding ones or where the performance level of API SP or lower and ACEA C2/C3 of the given viscosity grade is required.
The oil is not suitable for use in heavy trucks and similar vehicles!
