Motor Kaltreiniger – highly effective detergent for cleaning and maintenance of the engine compartment of the car. Quickly, efficiently and carefully removes any contamination of the engine compartment: oil, residues of evaporated and burnt technical fluids, road dirt and dust, road reagents, etc. Softens and dissolves the most difficult to remove and old dirt. A clean engine is less likely to overheat.
– Has an increased solvent capacity and active cleaning properties;
– Active foam stays on vertical surfaces for a long time, providing excellent cleaning of complex dirt in all dimensions;
– Neutral in relation to plastic, rubber, paint coatings, chrome, nickel, zinc, etc., as well as to the surfaces of ferrous and non-ferrous (aluminum, bronze, brass, etc.) metals and alloys;
– Further prevents oxidation, cracking and loss of properties of rubber and plastic parts of the engine under the aggressive influence of pollution and the environment, prevents oxidation of electrical connections, reduces the risk of short circuits, prevents fire of electrical wiring;
– Can be used for cleaning various aggregates of cars, motorcycles, trucks, tractors and other agricultural and construction equipment, as well as water equipment: chassis, filters, pumps, tools, auto and motorcycle drive chains of all types, garden equipment and tools;
– It is recommended to use at the end of the “dirty” season, before and after engine, suspension or transmission repairs, as well as during pre-sale preparation of the car;
– Can be used for cleaning concrete floors from oil.

Application: Spray on the parts to be cleaned from a distance of 20-30 cm and leave to act for 10-20 minutes, depending on the degree of contamination. Then rinse thoroughly with a strong stream of water.

Catalytic System Cleaner is a professional tool for cleaning and restoring the efficiency of catalytic converters. Suitable for all gasoline engines, both naturally aspirated and turbocharged, equipped with these systems. It also allows you to clean the power supply system and fuel injection devices of a gasoline engine from all typical contaminants without disassembly.

Properties:
– Cleans valves, piston rings, working surface – catalytic Converter cells, exhaust system from carbon deposits, tar and other deposits. Removes carbon deposits from the walls of the combustion chamber and from the grooves of the piston rings, preventing their occurrence;
– Helps to clean the oxygen sensor electrodes (lambda probe);
– Restores the original engine power by reducing the hydrodynamic resistance of the exhaust system;
– By optimizing the combustion process and eliminating contamination of the fuel and exhaust systems, it reduces fuel consumption and exhaust gas toxicity;
– In the future, with a long-term effect, it protects the catalytic converter from blockages, and the fuel system from corrosion;
– Increases the service life of the catalytic Converter and the entire exhaust system.

Application: connect the injection device to the cylinder. Insert (stick) its needle into the rubber hose of the engine air intake and hang the balloon upside down (for example, by the edge of the raised hood) as a dropper. Turn on the flow of funds. Allow the engine to idle at 1500 rpm for approximately 30-45 minutes. Do not allow the engine to overheat. If the exhaust manifold starts to glow red (due to high temperature), stop cleaning immediately.

Belt Tensioner – means for care of driving belts: quickly, safely and effectively eliminates extraneous sounds (creaking, whistling, etc.) and slipping of belts, cleans them from dirt, removes traces of oils, restores elasticity, protects against drying and cracking. It is used for drive belts of alternators, air conditioners, power steering and other units.

Properties:
– Reduces wear on belts and pulleys, prevents their aging, thereby extending their service life;
– Increases the efficiency of the belt drive;
– Reduces noise during operation of the engine;
– Especially effective for eliminating the slippage of old belts when they can not be replaced or stretched;
– Suitable for V-belts and semi V-belts, not suitable for flat belts;
– For belts made of leather, various fabrics impregnated with rubber or balata, chemical fibers, nylon, polyurethane and other synthetic materials;
– Regular use of the product extends the service life of the belts by 1.5–2 times.

Application:
Stop the belt drive. Spray a small amount of the product from a distance of approximately 20 cm on the pulley under the side surfaces of the belt and/or directly on the side surfaces themselves. Turn the belt drive at least one full turn of the belt so that the product is evenly distributed over the belt surface. Repeat the procedure one or more times if you want to achieve a greater thickness of the protective layer. After applying the last layer leave to act for 10 minutes before starting the engine again.

Anticor is a high – quality anti-corrosion and anti-gravel agent in the form of a liquid based on synthetic resins and rubbers. It is intended for processing of external and internal surfaces of a car body, a bottom, wheel arches, wings, aprons, lower surfaces of thresholds of cars, etc. It is suitable for processing the internal surfaces of the hood, doors, and body amplifiers. For professional body repairs, it is used to protect welds from inside of panels, protect the internal surfaces of new body panels, as well as to process fenders, doors, aprons, hoods, trunks, etc. before installing on the car.

Properties:
– Reliably protects the body from the negative effects of road salt and deicing reagents, all types of atmospheric effects, corrosion, protects from scratches caused by road surface particles (gravel, crushed stone, etc.);
– Has passivation properties, significantly slowing down the corrosion process that has already begun;
– Forms a strong, smooth, indelible elastic film with ticostropic properties (can be applied in a thick layer without forming smudges and self-leveling, and scratches on it are prone to self-tightening), resistant to mechanical influences, to moisture, salts, acids and alkalis after drying. Does not chip or wear during operation;
Effectively penetrates into the smallest crevices, displacing water from cracks, crevices and joints between the body panels, forms a waterproof layer;
– Has excellent adhesion – holds securely even on smooth, non-porous surfaces. It does not lose its adhesive properties at extremely high temperatures – it does not peel off and is securely held on a heated surface;
– Neutral to metals, plastics, rubbers and paint coatings;
– Resistant to extremely low temperatures, retains plasticity and does not crack;
– It has sound-proof and anti-vibration properties, significantly reducing road noise and vibrations of body elements, thereby increasing the comfort of driving;
– Dry quickly. The declared properties are acquired after complete drying.

Application: before applying the product, the surface must be thoroughly cleaned of rust, dirt and dust, grease, oil and other organic contaminants. For degreasing, we recommend using 9691 MANNOL Brake Cleaner. For best results, it is recommended to apply the product at room temperature.
The product is applied using a spray gun with a compressor at a pressure of 2 to 8 bar (depending on the desired fineness of the spray). Shake the balloon well before use. After pouring the product into the spray container, immediately close the balloon, as a film forms very quickly on the surface of the product. Spray with a layer of up to 1.5 mm at a distance of about 20-30 cm from the surface. Resistance to abrasion and corrosion increases with the thickness of the coating. For this reason, the spray process should be repeated once or twice after a short (1-2 minutes) drying time. To obtain a uniform coating and not to leave untreated areas, the spray must be carried out crosswise. The coating is not subject to further staining.
Depending on the thickness of the layer and weather conditions, the car is ready to move again in about 2 hours. Final drying takes 12-24 hours.

Intake Valve Cleaner-a highly effective tool for cleaning the intake system of gasoline engines up to the intake valves and in the most inaccessible places from all the typical dirt without disassembling the system. In most cases, a single application is sufficient to bring the intake system into perfect condition.
As the idling valve (IAC) is operating, deposits gradually accumulate on it, which ultimately affects the circulation of air and gases. This reduces engine power and acceleration, disrupts the smoothness of idling, and significantly increases fuel consumption. Signs of a clogged idle valve may include:
– Difficult start-up;
– Intermittent idling, as indicated by jumping tachometer readings;
– Slow speed reduction when you press the clutch pedal while driving;
– Black smoke from the exhaust pipe.

Properties:
– Quickly, effectively and carefully removes dirt, soot, carbon, resinous and oil deposits and other most difficult to remove and old dirt;
– Further protects the intake system elements from corrosion and oxidation, prevents the formation of new dirt and deposits on them, provides functionality and mobility of moving parts, – extending the service life of the intake system and reducing repair costs;
– Facilitates cold start, restores the uniformity of idle speed, and reduces fuel consumption;
– Contains acetone-aggressive to paint surfaces and plastics;
– Safe for catalytic converters, oxygen sensors and turbochargers.

Application: shake the balloon well before use. The product must be sprayed behind the air flow meter (the product must not get on it) for at least 30 seconds (depending on the degree of contamination) when the engine is idling (at least 2000 rpm).
If there are particularly persistent deposits on the throttle, inside the intake manifold, or on the intake valves, the cleaning procedure can be repeated. After application, allow the engine to run for about 20 seconds at min. 2000 rpm, so that possible residues in the intake system can burn.

Motor Cleaner is a detergent for cleaning and care of the engine compartment of the vehicle. Quickly, efficiently and carefully removes most of the typical engine compartment dirt: oils, residues of evaporated and burnt technical fluids, road dirt and dust, road reagents, etc. It has a high cleaning capacity. A clean engine is less likely to overheat.
– Has an increased solvent capacity and active cleaning properties;
– High-viscosity concentration allows components to remain on vertical surfaces, providing excellent cleaning of complex contaminants in all dimensions;
– Neutral in relation to coatings made of chrome, nickel, zinc, etc., as well as to the surfaces of ferrous and non-ferrous (aluminum, bronze, brass, etc.) metals and alloys. It can be aggressive towards certain types of plastics, rubbers and paint coatings;
– Further prevents oxidation, cracking and loss of properties of rubber and plastic parts of the engine under the aggressive influence of pollution and the environment, prevents oxidation of electrical connections, reduces the risk of short circuits, prevents fire of electrical wiring;
– Can be used for cleaning various units of cars, motorcycles, trucks, tractors and other agricultural, garden and construction equipment, as well as water equipment: chassis, filters, pumps, auto and motorcycle-free drive chains, etc. , as well as various inventory and working tools;
– It is recommended to use at the end of the “dirty” season, before and after engine, suspension or transmission repairs, as well as during pre-sale preparation of the car.

Application: Spray the product on the parts to be cleaned from a distance of 15-20 cm, holding the container vertically. Leave to act for 3-5 minutes, depending on the degree of contamination. Wipe with a brush or sponge, and then rinse with water. Repeat the procedure if necessary. Before applying, try the cleaner on a small inconspicuous area to find out possible reactions with different materials.